Abstract:The High Luminosity Large Hadron Collider (HL-LHC [1]), an upgrade of the LHC, is set to become operational in 2029, aiming to achieve instantaneous luminosities 5–7.5 times larger than the nominal value of the LHC. However, unlocking the full physics potential at this much higher luminosity level necessitates a tenfold increase in the data bandwidth processed by ATLAS. This poses significant challenges to the design of the Trigger and Data Acquisition systems. To address these challenges, a baseline architecture has been chosen for the ATLAS Phase-II upgrade, relying on a single-level hardware trigger known as the Level-0 Trigger. This trigger has a maximum rate of 1 MHz and a latency of 10 μs. Central to this upgrade is the inclusion of a new subsystem — the Global Trigger [2]. This component performs complex algorithms, akin to those currently used in Phase-I high-level trigger software (such as Topoclustering), on full-granularity calorimeter data. The Global Trigger is divided into three sublayers: the Multiplexer Processor (MUX) layer, the Global Event Processor (GEP) layer, and the Global to Central Trigger Processor [3] interface (gCTPi). A full-function Global Common Module (GCM) hardware prototype has been designed to fulfill the requirements of all three sublayers of the Global Trigger, featuring different firmware loads. This GCM prototype, based on the ATCA [4] front board form factor, incorporates two of the latest AMD (Xilinx) Versal Premium devices VP1802 [5]. These devices boast double the density of the Virtex UltraScale+ FPGA VU13P used in the previous design [6] and include an integrated SoC with a completely new architecture. To handle high-speed I/Os, this GCM prototype employs twenty 12-channel 25.7 Gb/s FireFly [7] optical engines. The estimated maximum power consumption of this GCM prototype is 400 W, which falls within the cooling capabilities of the ATLAS ATCA shelf. To ensure power integrity, signal integrity, and thermal performance, extensive PCB simulations and thermal simulations have been done to guide the layout design of the GCM prototype. This paper provides an in-depth overview of the design process for this full-function GCM prototype hardware, with a particular focus on technology choices and simulation results.

Development and data path integration test of the global Feature EXtractor for the ATLAS Level-1 calorimeter trigger system Phase-I upgrade

The Development of Global Feature Extractor (gfex) – the ATLAS Calorimeter Level 1 Trigger for ATLAS at High Luminosity LHC

The Development of the Global Feature Extractor for the LHC Run-3 Upgrade of the L1 Calorimeter Trigger System

The Prototype Design of Gfex — a Component of the L1calo Trigger for the ATLAS Phase-I Upgrade

Gfex, the ATLAS Calorimeter Level-1 Real Time Processor

Design and Evaluation of the LAr Trigger Digitizer Board in the ATLAS Phase-I Upgrade

FELIX: the New Detector Interface for the ATLAS Experiment

A full-function Global Common Module prototype for ATLAS Phase-II upgrade

A prototype optical link board with redundancy design for the ATLAS liquid argon calorimeter Phase-2 upgrade

Characterization of the ATLAS Liquid Argon Front-End ASIC ALFE2 for the HL-LHC upgrade

Design and hardware evaluation of the optical-link system for the ATLAS Liquid Argon Calorimeter Phase-II Upgrade

Development of an ADC radiation tolerance characterization system for the upgrade of the ATLAS LAr calorimeter

The Clock and Control System for the ATLAS Liquid Argon Calorimeter Phase-I Upgrade

The Phase-I Trigger Readout Electronics Upgrade of the ATLAS Liquid Argon Calorimeters

FELIX based readout of the Single-Phase ProtoDUNE detector

Upgrade of the ATLAS Level-0 TGC Endcap Muon Trigger for HL-LHC

Design of the CMS High Granularity Calorimeter trigger primitive generator system

Design of the Compact Processing Module for the ATLAS Tile Calorimeter

CMS ECAL VFE design, production and testing

System design and prototyping of the CMS Level-1 Trigger at the High-Luminosity LHC