Abstract:The High Luminosity Large Hadron Collider (HL-LHC [1]), an upgrade of the LHC, is set to become operational in 2029, aiming to achieve instantaneous luminosities 5–7.5 times larger than the nominal value of the LHC. However, unlocking the full physics potential at this much higher luminosity level necessitates a tenfold increase in the data bandwidth processed by ATLAS. This poses significant challenges to the design of the Trigger and Data Acquisition systems. To address these challenges, a baseline architecture has been chosen for the ATLAS Phase-II upgrade, relying on a single-level hardware trigger known as the Level-0 Trigger. This trigger has a maximum rate of 1 MHz and a latency of 10 μs. Central to this upgrade is the inclusion of a new subsystem — the Global Trigger [2]. This component performs complex algorithms, akin to those currently used in Phase-I high-level trigger software (such as Topoclustering), on full-granularity calorimeter data. The Global Trigger is divided into three sublayers: the Multiplexer Processor (MUX) layer, the Global Event Processor (GEP) layer, and the Global to Central Trigger Processor [3] interface (gCTPi). A full-function Global Common Module (GCM) hardware prototype has been designed to fulfill the requirements of all three sublayers of the Global Trigger, featuring different firmware loads. This GCM prototype, based on the ATCA [4] front board form factor, incorporates two of the latest AMD (Xilinx) Versal Premium devices VP1802 [5]. These devices boast double the density of the Virtex UltraScale+ FPGA VU13P used in the previous design [6] and include an integrated SoC with a completely new architecture. To handle high-speed I/Os, this GCM prototype employs twenty 12-channel 25.7 Gb/s FireFly [7] optical engines. The estimated maximum power consumption of this GCM prototype is 400 W, which falls within the cooling capabilities of the ATLAS ATCA shelf. To ensure power integrity, signal integrity, and thermal performance, extensive PCB simulations and thermal simulations have been done to guide the layout design of the GCM prototype. This paper provides an in-depth overview of the design process for this full-function GCM prototype hardware, with a particular focus on technology choices and simulation results.

System design and prototyping of the CMS Level-1 Trigger at the High-Luminosity LHC

The CMS Trigger Upgrade for the HL-LHC

The CMS Level-1 Trigger at LHC and Super-LHC

The CMS High Level Trigger: Commissioning and First Operation with LHC Beams

Architecture of a Level 1 Track Trigger for the CMS Experiment

Design of the CMS High Granularity Calorimeter trigger primitive generator system

The CMS High Level Trigger

Level-1 Track Finding with an all-FPGA System at CMS for the HL-LHC

Adaptability and efficiency of the CMS Level-1 Global Trigger firmware implementation for Phase-2

A full-function Global Common Module prototype for ATLAS Phase-II upgrade

A CMS Level-1 Track Finder for the HL-LHC

The Trigger System of the CMS Experiment

Trigger and Data Acquisition for hadron colliders at the Energy Frontier

Summary of the trigger systems of the Large Hadron Collider experiments ALICE, ATLAS, CMS and LHCb

The High-Level Trigger for the CMS Phase-2 Upgrade

Upgrade of the ATLAS Level-0 TGC Endcap Muon Trigger for HL-LHC

Run 2 Upgrades to the CMS Level-1 Calorimeter Trigger

Design and implementation of neural network based conditions for the CMS Level-1 Global Trigger upgrade for the HL-LHC

ATLAS hardware-based Endcap Muon Trigger for future upgrades

The Prototype Design of Gfex — a Component of the L1calo Trigger for the ATLAS Phase-I Upgrade

The ATLAS Level-1 Trigger: Status of the System and First Results from Cosmic-Ray Data