Abstract:The ATLAS detector is installed in its experimental cavern at Point 1 of the CERN Large Hadron Collider. During Run 2 of the LHC, a luminosity of $\mathcal{L}=2\times 10^{34}\mathrm{cm}^{-2}\mathrm{s}^{-1}$ was routinely achieved at the start of fills, twice the design luminosity. For Run 3, accelerator improvements, notably luminosity levelling, allow sustained running at an instantaneous luminosity of $\mathcal{L}=2\times 10^{34}\mathrm{cm}^{-2}\mathrm{s}^{-1}$, with an average of up to 60 interactions per bunch crossing. The ATLAS detector has been upgraded to recover Run 1 single-lepton trigger thresholds while operating comfortably under Run 3 sustained pileup conditions. A fourth pixel layer 3.3 cm from the beam axis was added before Run 2 to improve vertex reconstruction and $b$-tagging performance. New Liquid Argon Calorimeter digital trigger electronics, with corresponding upgrades to the Trigger and Data Acquisition system, take advantage of a factor of 10 finer granularity to improve triggering on electrons, photons, taus, and hadronic signatures through increased pileup rejection. The inner muon endcap wheels were replaced by New Small Wheels with Micromegas and small-strip Thin Gap Chamber detectors, providing both precision tracking and Level-1 Muon trigger functionality. Tile Calorimeter scintillation counters were added to improve electron energy resolution and background rejection. Upgrades to Minimum Bias Trigger Scintillators and Forward Detectors improve luminosity monitoring and enable total proton-proton cross section, diffractive physics, and heavy ion measurements. These upgrades are all compatible with operation in the much harsher environment anticipated after the High-Luminosity upgrade of the LHC and are the first steps towards preparing ATLAS for the High-Luminosity upgrade of the LHC. This paper describes the Run 3 configuration of the ATLAS detector.

Overview of the ATLAS High-Granularity Timing Detector: project status and results

Performance in beam tests of Carbon-enriched irradiated Low Gain Avalanche Detectors for the ATLAS High Granularity Timing Detector

Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector

Low gain avalanche detectors for precision timing in the CMS MTD endcap timing layer

The High-Level Trigger for the CMS Phase-2 Upgrade

Upgrade of the ATLAS Level-0 TGC Endcap Muon Trigger for HL-LHC

Performance of a Front End prototype ASIC for picosecond precision time measurements with LGAD sensors

Beam Test Results of NDL Low Gain Avalanche Detectors (LGAD)

The CMS High-Granularity Calorimeter for Operation at the High-Luminosity LHC

Design of the CMS High Granularity Calorimeter trigger primitive generator system

Design and performance of a TDC ASIC for the upgrade of the ATLAS Monitored Drift Tube detector

Low Gain Avalanche Detectors with Good Time Resolution Developed by IHEP and IME for ATLAS HGTD project

Design and Evaluation of the LAr Trigger Digitizer Board in the ATLAS Phase-I Upgrade

Upgrade of the ATLAS Muon Trigger for the SLHC

ATLAS hardware-based Endcap Muon Trigger for future upgrades

The CMS Trigger Upgrade for the HL-LHC

The muon high level trigger of the ATLAS experiment

The ATLAS Experiment at the CERN Large Hadron Collider: A Description of the Detector Configuration for Run 3

A Low-Power Time-to-Digital Converter for the CMS Endcap Timing Layer (ETL) Upgrade

The ATLAS Level-1 Trigger: Status of the System and First Results from Cosmic-Ray Data

Design of a Time-to-Digital Converter ASIC and a mini-DAQ system for the Phase-2 upgrade of the ATLAS Monitored Drift Tube detector