Abstract:A two-step time-to-digital converter (TDC) is designed for the high-precision time measurement of the DIRC-like TOF (DTOF) detector at the Super Tau-Charm Facility (STCF). Extending the measurement range by Nutt's method, the TDC clock cycle is interpolated with two voltage-controlled tapped delay lines (TDL) connected by a dual-slope time amplifier (TA). By amplifying the residue from the first-step TDL-based interpolation with the TA and measuring it with the second TDL, the TDC resolution is significantly improved to sub-gate delay. Since the residue is extracted by a new method without the need of TA duplication or delay insertion, the TDC power consumption and conversion time are effectively reduced. By adopting the improved TA circuit into the TDC with a high gain, adjustable output offsets, and good linearity, the TDC measurement precision is guaranteed. In addition, a new DLL structure is proposed to stabilize the TDL against process, voltage, and temperature (PVT) variations with less power consumption. Benefiting from the proposed residue extraction method and DLL structure, the TDC exhibits low power consumption. To verify the TDC design, a prototype chip with two TDC channels is fabricated in GlobalFoundries (GF) 180 nm CMOS technology for performance evaluation. With a system clock of 150 MHz, it has a resolution (LSB) of 16.5 ps and a maximum sample rate of 6 MS/s. The differential nonlinearity (DNL) error ranges from - 0.98 LSB to 0.87 LSB and the integral nonlinearity error (INL) ranges from- 4.21 LSB to 2.83 LSB. With a bin-by-bin calibration method, the measured TDC precision is 12.1 ps on average within the 0-20 ns time interval measurement range. In addition, the TDC has low temperature sensitivity and does not require recalibration within a 20 C-degrees temperature range. Each TDC channel consumes 434 mu W power at 1 MS/s sample rate. The test results confirm that the proposed TDC can achieve high precision with a moderate sample rate and low power consumption without highly scaled technologies, which can meet the requirements of the DTOF detector at STCF.

TPC Readout Electronics with Time-to-Digital Converters

Development of a Low Power and High Integration Readout ASIC for Time Projection Chambers in 65 Nm CMOS

A Low-Power Time-to-Digital Converter for the CMS Endcap Timing Layer (ETL) Upgrade

A Sub-10ps Resolution Multichannel Time-to-Digital Converter with Two-Stage Interpolation for High-Energy Physics Applications

Status and prospects of TPC module and prototype at high luminosity <i>Z</i> physics on CEPC

WASA: a low power and high integration readout ASIC for TPCs in 65 nm CMOS

A 12 Ps Precision Two-Step Time-to-Digital Converter Consuming 434 $\mu$ W at 1 MS/s in 180 Nm CMOS with a Dual-Slope Time Amplifier

A Prototype Design of the Readout Electronics of MRPC Detectors in CEE in HIRFL

Characterization of the CMS Endcap Timing Layer Readout Chip Prototype with Charge Injection

The ALICE TPC: Optimization of the Performance in Run 2 and Developments for the Future

Performance of TPC Detector Prototype Integrated with UV Laser Tracks for the Circular Collider

Energy And Timing Measurement Of A Pet Detector With Time-Based Readout Electronics

A Time Projection Chamber with GEM-based Readout

A High-Density Time-to-Digital Converter Prototype Module for BES III End-Cap TOF Upgrade

Fundamental noise limitations to supercontinuum generation in microstructure fiber

Energy and Timing Measurement with Time-Based Detector Readout for PET Applications: Principle and Validation with Discrete Circuit Components.

Casca: A Readout Asic For A Tpc Based X-Ray Polarimeter

A Front-End Electronics Module for Multi-gap Resistive Plate Chambers

ALICE TPC upgrade for High-Rate operations

Performance of the continuous ions suppression TPC prorotype for circular collider

A time-to-digital converter with steady calibration through single-photon detection