Abstract:The metallic interconnects are essential components of energy devices such as fuel cells and electrolysis cells, batteries, as well as electronics and optoelectronic devices. In recent years, 3D printing processes have offered complementary routes to the conventional photolithography- and vacuum-based processes for interconnect fabrication. Among these methods, the confined electrodeposition (CED) process has enabled a great control over the microstructure of the printed metal, direct printing of high electrical conductivity (close to the bulk values) metals on flexible substrates without a need to sintering, printing alloys with controlled composition, printing functional metals for various applications including magnetic applications, and for in situ scanning electron microscope (SEM) nanomechanical experiments. However, the metal deposition rate (or the overall printing speed) of this process is reasonably slow because of the chemical nature of the process. Here, we propose using the CED process to print a single layer of a metallic trace as the seed layer for the subsequent selected-area electroless plating. By controlling the activation sites through printing by the CED process, we control, where the metal grows by electroless plating, and demonstrate the fabrication of complex thin-film patterns. Our results show that this combined process improves the processing time by more than 2 orders of magnitude compared to the layer-by-layer printing process by CED. Additionally, we obtained Cu and Ni films with an electrical resistivity as low as ∼1.3 and ∼2 times of the bulk Cu and Ni, respectively, without any thermal annealing. Furthermore, our quantitative experiments show that the obtained films exhibit mechanical properties close to the bulk metals with an excellent adhesion to the substrate. We demonstrate potential applications for radio frequency identification (RFID) tags, for complex printed circuit board patterns, and resistive sensors in a Petri dish for potential biological applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01890?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01890</a>.SEM images of the single-layer printed Cu and Ni lines with a nozzle diameter of ∼250 μm for different nozzle speeds; The optical images of single-layer Cu and Ni lines printed with different nozzle speeds, and the width and thickness of the printed Cu and Ni lines vs the nozzle speed; The FIB-sectioned cross-sectional images of Cu and Ni films; and The schematic of an unpinned (top) and pinned (bottom) indentation-induced buckle (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01890/suppl_file/am1c01890_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Next Generation of 3D‐Printed Electronics: Electroplating Inside Channels to Embed 3D Copper Features within Polymeric Structures Fabricated Through Material Extrusion

3D Printed Electronics With High Performance, Multi-Layered Electrical Interconnect

Intercircuit: Electroplating with Cavities for Fast Fabrication of Complex and High-Performance 3D Circuits

Sustainable direct metallization of 3D-printed metal-infused polymer parts: a novel green approach to direct copper electroless plating

Fabrication of polyetheretherketone (PEEK)-based 3D electronics with fine resolution by a hydrophobic treatment assisted hybrid additive manufacturing method

Direct electroless plating of conductive thermoplastics for selective metallization of 3D printed parts

Solution-based, additive fabrication of flush metal conductors in plastic substrates by printing and plating in two-level capillary channels

Interconnect Fabrication by Electroless Plating on 3D-Printed Electroplated Patterns

Form‐Factor Free 3D Copper Circuits by Surface‐Conformal Direct Printing and Laser Writing

3D Printing for Functional Electronics by Injection and Package of Liquid Metals into Channels of Mechanical Structures

Laser‐Activated Selective Electroless Plating on 3D Structures via Additive Manufacturing for Customized Electronics

Fabrication of Shape‐Controlled Copper Line Arrays by Meniscus‐Confined 3D Microprinting on Insulating Substrates

Selectively Metalizable Stereolithography Resin for Three-Dimensional DC and High-Frequency Electronics via Hybrid Additive Manufacturing

One‐Stop Hybrid Printing of Bulk Metal and Polymer for 3D Electronics

Direct 3D Printing of Stretchable Circuits via Liquid Metal Co‐Extrusion Within Thermoplastic Filaments

Hybrid 3D Printing of Molten Metal Microdroplets and Polymers for Prototyping of Printed Circuit Boards Featuring Interdigitated 3D Capacitors

Microstructure-driven electrical conductivity optimization in additively manufactured microscale copper interconnects

Light‐Based 3D Multi‐Material Printing of Micro‐Structured Bio‐Shaped, Conducting and Dry Adhesive Electrodes for Bioelectronics

Copper electroplating of 3D printed composite electrodes

Patternable, High-Precision, Controllable Wettability Copper Layers for 3D Resin-Based Weather-Resistant Electronics and 3D Liquid Manipulation

Electrohydrodynamic Redox 3D Printing: Confined Electroplating of Alloys for Additive Manufacturing at the Submicron Scale