Abstract:Microstructure formation in coarse-grained heat-affected zones (CGHAZs) of bainitic steel welds under multiple welding thermal cycles was investigated by microstructure characterization and finite element modeling. The impact toughness and fatigue crack growth resistance for the CGHAZs were further examined, and the correlation between microstructure and mechanical properties was clarified. The CGHAZ at weld root (CGHAZ-R) experienced three welding thermal cycles with peak temperatures of 1198, 892 and 603 °C, respectively. The microstructure at the CGHAZ-R evolved into fine lath bainite after the first-layer welding, and then transformed into fine polygonal ferrite and granular bainite with refined martensite–austenite (M-A) islands after the second-layer welding. Finally, the M-A islands were tempered during the third-layer welding. For the CGHAZ at the weld toe (CGHAZ-T), the peak temperatures of three thermal cycles were 525, 1022 and 1250 °C, respectively. Its resultant microstructure was composed of lath bainite and granular bainite due to the intermediate cooling rate in the last thermal cycle. Electron backscatter diffraction results show that the density of high angle grain boundary (HAGB) at the CGHAZ-R was higher than that at the CGHAZ-T. Compared to the CGHAZ-T, the CGHAZ-R presented superior impact toughness and a lower fatigue crack growth rate. The higher impact toughness of CGHAZ-R was because of the higher plastic deformation capacity of polygonal ferrite and the tempered fine M-A islands. The retarded fatigue crack growth of CGHAZ-R was due to the numerous crack deflections induced by the high-density HAGB and the high plastic deformability of the polygonal ferrite.

Study on Microstructure and Low‐Temperature Impact Toughness in Coarse Grain Heat‐Affected Zone of EH460 Steel

Effect of Welding Peak Temperature on Microstructure and Impact Toughness of Heat-Affected Zone of Q690 High Strength Bridge Steel

Effect of welding heat input on microstructure and impact toughness in CGHAZ of X100Q steel

Favorable Impact Toughness of High Heat Input Coarse-Grained HAZ in an Ultra-Low Carbon High-Strength Microalloyed Steel

Significant influence of heat input on microstructure evolution and mechanical properties of the simulated CGHAZ in a 1000 MPa grade ultra-high strength steel

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Improvement of impact toughness by microstructure refinement of simulated CGHAZ through enhancing welding heat input of low carbon Mo-V-Ti-N-B steel

Elucidating the heat input on CGHAZ microstructure and its irregular effect on impact toughness for a novel V-N microalloying weathering steel

Microstructure and mechanical properties of thermal simulation CGHAZ of DP780 high strength steel

Effect of Microstructure on Impact Toughness and Fatigue Performance in Coarse-Grained Heat-Affected Zone of Bainitic Steel Welds

Mechanism of Interfacial Microstructure Evolution of G115 Steel in Simulated Heat Affected Zone

Effect of Pre-Weld Heat Treatment on the Microstructure and Properties of Coarse-Grained Heat-Affected Zone of a Wind Power Steel after Simulated Welding

Coarse Grain Heat Affect Zone Microstructures and Toughness of X80 Pipeline Steel

Effect of Heat Input on Microstructure and Properties in Heat Affected Zone of Astm A572 Gr.65 Steel

Microstructure and Low-Temperature Toughness of Reheated Coarse-Grained Heat-Affected Zone of 06Ni9DR Steel

Toughness of Heat-Affected Zone of 800 Mpa Grade Low Alloy Steel

Effect Of Welding Heat Input On The Microstructure And Toughness In Simulated Cghaz Of 800 Mpa-Grade Steel For Hydropower Penstocks

Revealing the mechanism of crack initiation and propagation in CGHAZ of S690QL welded joints through low-temperature impact tests with gradient setting of pendulum angle

Influence of welding HAZ microstructure on low-temperature impact fracture behaviour in C–Mn shipbuilding steel

On the role of Cu addition in toughness improvement of coarse grained heat affected zone in a low carbon high strength steel