Abstract:The hot deformation characteristics. of as-cast nickel-base superalloy GH742y after hot isostatic pressing (HIP)(hereafter referred to as-cast alloy) have been investigated by hot compression tests in the temperature range of 1050 to 1140 degrees C, strain rate range of 0.01 s(-1) to 10 s(-1) and strain range of 35% to 50% by means of Gleeble-3500 thermal mechanical simulator. The results show that the as-cast alloy exhibits the poor deformability,and shows wedge-shaped cracking beyond the strain of 35%. At strain rates less than 1.0 s(-1), the stress-strain curves exhibit nearly steady-state behavior, while at strain rate of 10 s(-1), a yield drop and serrated yielding occur. The activation energy values developed on the basis of the experimental data are divided into three domains. The first domain appears at lower strain rate (<= 1.0 s(-1)) and lower temperature (<= 1080 degrees C), with the lowest mean value of activation energy about 261.4 kJ/mol. The second domain appears at the same strain rate as the first domain, but higher temperature (>1080 degrees C), with the intermediate mean value of activation energy about 328.8 kJ/mol. The third domain appears at higher strain rate (10 s(-1)) and temperature range of 1050 to 1140 degrees C, with the largest mean value of activation energy about 605.05 kJ/mol. Three different constitutive equations are established in corresponding to domains. Microstructural observations in the third domain reveal non-uniform dynamic recrystallization (DRX) of homogeneous gamma phase, which leads to the poor deformability and the highest Q value. In contrast, microstructures in the first domain show fully DRX of homogeneous gamma phase, leading to the better deformability and the lowest Q value. It is noted that the grain size increases with the increment of strain rate or temperature. These results suggest that bulk metal working of this material may be carried out in the first domain where fully DRX of gamma homogeneous occurred.

Effect of hot isostatic pressing on stress-rupture crack growth of a single-crystal nickel-based superalloy

New insights into the stress rupture life enhancement mechanisms of a nickel-based superalloy

Application of Hot Isostatic Pressing in Nickel-Based Single Crystal Superalloys

On the Impact of an Integrated HIP Treatment on the Very High Cycle Fatigue Life of Ni-Based SX Superalloys

Effect of hot isostatic pressing on microstructures and properties of superalloy K4169

Hot Deformation Characteristics for a Nickel-base Superalloy GH742y

Effect of HIP treatment on the microstructure and mechanical properties of a Ni-based superalloy fabricated by selective laser melted method

Effect of the Powder Size Distribution on the Hot Deformation Behavior of a Novel Nickel-based Powder Metallurgy Superalloy

Effect of Overheating Treatment on Microstructure and Stress Rupture Properties of a Nickel-Based Single-Crystal Superalloy

Effects of Heat Treatments on the Microstructure and Tensile Properties of IN738 Superalloy with High Carbon Content Fabricated Via Laser Powder Bed Fusion

Effect of grit blasting and subsequent heat treatment on stress rupture property of a Ni-based single-crystal superalloy SGX3

Heat-affected Zone Crack Healing in IN939 Repaired Joints Using Hot Isostatic Pressing

Effects of Hot Isostatic Pressing Temperature on Casting Shrinkage Densification and Microstructure of Ti6Al4V Alloy

CHARACTERISTICS OF HOT COMPRESSION DEFORMATION AND MICROSTRUCTURE EVOLUTION OF SPRAY FORMED NICKEL BASE SUPERALLOY

Near‐Net Shape Hot Isostatic Pressing: Microstructural Analysis and Hardness Evolution at a Steel–Nickel Alloy Interface

Simultaneously improved the strength and ductility of laser powder bed fused Al-Cr-Fe-Ni-V high-entropy alloy by hot isostatic pressing: Microcrack closure and precipitation strengthening

Effect of Hot Isostatic Pressing Process Parameters on Properties and Fracture Behavior of Tungsten Alloy Powders and Sintered Bars

Effect of Hot Isostatic Pressing Conditions and Cooling Rate on Microstructure and Properties of Ti-6al-4v Alloy from Atomized Powder

Effect of post-treatment on the microstructure and tensile properties of Ni–Co-based superalloy manufactured by selective laser melting

Effect of hot isostatic pressing on the mechanical and corrosive properties of Ti–Ni alloy fabricated by selective laser melting

Fracture Mechanisms Induced by Microporosity and Precipitates in Isothermal Fatigue of Polycrystalline Nickel Based Superalloy