Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Improvement of fracture toughness of Nb-Si alloy by two-step heat treatment

New Route to Improve the Fracture Toughness and Flexural Strength of Si3N4 Ceramics by Adding FeSi2

Effects of the microstructure and minor elements on the fracture toughness of Nb-Si alloy

Balancing the fracture toughness and tensile strength by multiple additions of Zr and Y in Nb–Si based alloys

Microstructural evolution during annealing of a powder metallurgical TiAl–Nb composite and its effect on mechanical properties

Achieving an appropriate strength-ductility synergy of Nbss/Nb5Si3 in situ composites governed by gradient annealing heat treatment

Secondary crystalline phases and mechanical properties of heat-treated Si3N4

Microstructure evolution and fracture toughness of Nb–Si–Ti based alloy with Cr, Mo and W elements addition

Optimizing the microstructure and mechanical behaviors of bimodal Mo-Si-B alloy by heat treatment

Synchronous improvement in room-temperature fracture toughness and high-temperature oxidation resistance of Nb Si based alloys with Erbium addition

Microstructure and mechanical properties of Nb 16Si alloys with Zr additions

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Micromechanism in fracture toughness of NbCr2 laves phase improved by nickel alloying: first-principles calculation

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Trace Strontium Addition on Microstructure and Room Temperature Fracture Toughness of Nb-12Si-22Ti Alloys

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Fracture Behavior and Mechanism of Nb-Si-Based Alloys with Heterogeneous Layered Structure

Improvement for creep strength of a second-generation single crystal superalloy by design of heat treatments

Mechanical properties and microstructure evolution of NbSiZr based alloy

Effect of Growth Rate on Microstructure and Mechanical Properties in a Directionally Solidified Nb-silicide Base Alloy

Effect of Heat Treatment on the Microstructure and Fracture Behaviors of a Ni–Cr–Fe Superalloy