Abstract:Silicon carbide (SiC) devices have the potential to yield new components with functional capabilities that far exceed components based on silicon devices. Selective doping of SiC by ion implantation is an important fabrication technology that must be completely understood if SiC devices are to achieve their potential. One major problem with ion implantation into SiC is the surface roughening that results from annealing SiC at the high temperatures which are needed to activate implanted acceptor ions, boron or aluminum. This paper examines the causes and possible solutions to surface roughening of implanted and annealed 4H-SiC. Samples consisting of n-type epilayers (5 × 1015 cm−3, 4 µm thick) on 4H-SiC substrates were implanted with B or Al to a total dose of 4 × 1014 cm−2 or 2 × 1015 cm−2, respectively. Roughness measurements were made using atomic force microscopy. From the variation of root mean square (rms) roughness with annealing temperature, apparent activation energies for roughening following implantation with Al and B were 1.1 and 2.2 eV, respectively, when annealed in argon. Time-dependent activation and surface morphology analyses show a sublinear dependence of implant activation on time; activation percentages after a 5 min anneal following boron implantation are about a factor of two less than after a 40 min anneal. The rms surface roughness remained relatively constant with time for anneals in argon at 1750°C. Roughness values at this temperature were approximately 8.0 nm. Annealing experiments performed in different ambients demonstrated the benefits of using silane to maintain good surface morphology. Roughnesses were 1.0 nm (rms) when boron or aluminum implants were annealed in silane at 1700°C, but were about 8 and 11 nm for B and Al, respectively, when annealed in argon at the same temperature.

Preparation of atomically clean and flat Si(100) surfaces by low-energy ion sputtering and low-temperature annealing

Atomically Flat Surface Preparation for Surface-Sensitive Technologies

Nanopatterning of Si(110) Surface by Ion Sputtering: an Experimental and Simulation Study

Nanostructuring of Si(100) by Normal-Incident Ar+ Ion Sputtering at Low Ion Flux

Preparation of atomically-flat SrTiO3 surfaces using a deionized-water etching and thermal annealing procedure

Development of procedures for obtaining clean, low-defect-density Ge(100) surfaces

Phase transition on the Si(001) clean surface prepared in UHV MBE chamber: A study by high resolution STM and in situ RHEED

Atomic layer etching of SiO$_2$ using sequential exposures of Al(CH$_3$)$_3$ and H$_2$/SF$_6$ plasma

Patterned growth of self-assembled silicon nanostructures by ion implantation and electron beam annealing

Surface Morphology Evolution of Si(110) by Ion Sputtering As A Function of Sample Temperature

Surface And Interface Study Of U/Si (111)

Unprecedented atomic surface of silicon induced by environmentally friendly chemical mechanical polishing

Formation of SiC-surface nanocrystals by ion implantation and electron beam rapid thermal annealing

Atomically Flat GaAs(001) Surfaces Obtained by High-Temperature Treatment with Atomic Hydrogen Irradiation

Formation of ultralow-reflectance silicon surface by dry etching

Preparation of Hydrophobic/Superhydrophobic Surface on Silicon Wafer by Reactive Ion Etching and Self-assembled Monolayers

Uniform broad-area deposition and patterning of SiO2 nanofilms by 172 nm photochemical conversion of liquid tetraethoxysilane layers at 300 K

Laser Induced Surface Nanostructuring on Ultra-Thin Amorphous Si Films

Fabrication of Functional Structures at Si (100) Surface by Mechanical Scribing in the Presence of Aryl Diazonium Salts

Successful Cleaning and Study of Contamination of Si(001) in Ultrahigh Vacuum

Surface roughening in ion implanted 4H-silicon carbide