Abstract:Solar cells have attracted much attention since they can convert solar energy directly into electricity, and have been widely utilized in manufacturing industry and people's daily life. Although the power conversion efficiency (PCE) of single-junction solar cells has gradually improved in recent years, its maximum efficiency is restricted by the Shockley-Queisser (SQ) limit of single-junction solar cells. To exceed the SQ limit and further obtain high efficiency solar cells, researchers have proposed the concept of tandem solar cells. In this work, a systematic theoretical study of chalcopyrite CuGaSe 2 /CuInSe 2 tandem solar cells was carried out by combining first-principle calculations and SCAPS-1D device simulations. Firstly, the electronic structure, defect properties and corresponding macroscopic performance parameters of CuGaSe 2 (CGS) were obtained by first-principles calculations, which were adopted as input parameters for subsequent device simulations of CGS solar cells. Subsequently, the simulations of single-junction CGS and CuInSe 2 (CIS) solar cells were carried out using SCAPS-1D software, respectively. The simulation results for the single junction CIS solar cells are in good agreement with the experimental values. For single-junction CGS cells, the device simulations revealed that CGS single-junction solar cells had the highest short-circuit current (J sc ) and PCE at the growth condition of Cu-rich, Ga-rich and Se-poor chemical growth condition. Further optimization found that the open-circuit voltage (V oc ) and PCE of CGS solar cells can be improved by replacing the electron transport layer (ETL) with ZnSe after the devices with the highest short-circuit current (J sc ). Finally, after the optimized CGS and CIS solar cells were connected in series with two-terminal (2T) monolithic tandem solar cell, the device simulation results show that under the growth temperature of 700 K and the growth environment of Cu-rich, Ga-rich, and Se-poor, with ZnSe as the ETL, the CGS thickness of 2000 nm and the CIS thickness of 1336 nm, the PCE of 2T monolithic CGS/CIS tandem solar cell can reach 28.91 %, which is higher than the recorded efficiency of the current single-junction solar cells, and shows a good application prospect.

Design and optimization of two-terminal InGaP/Si tandem solar cell through numerical simulation

Simulation of the Efficiency of a-SiC:H/a-Si:H Tandem Multilayer Solar Cells

Maximizing efficiency: Numerical modeling and optimization of 2-terminal perovskite/silicon tandem devices with different bottom cell structures

Comprehensive Design and Analysis of Thin Film Sb2S3/CIGS Tandem Solar Cell: TCAD Simulation Approach

Numerical simulation of InGaN Schottky solar cell

Top cell design and optimization of all-chalcopyrite CuGaSe 2 /CuInSe 2 two-terminal tandem solar cells: first-principles calculations and device simulations

Simulation of the Efficiency of CdS/CIGS Tandem Multi-Junction Solar Cells Using AMPS-1D

Technological guidelines for the design of tandem III-V nanowire on Si solar cells from opto-electrical simulations

Performance and optimization study of selected 4-terminal tandem solar cells

High-efficiency InP-based Multijunction Solar Cells

Design and Simulation of a‐Si:H/PbS Colloidal Quantum Dots Monolithic Tandem Solar Cell for 12% Efficiency

Efficiency Boosting of 4-T Bifacial Dual-Textured Perovskite/Perl Silicon Tandem Solar Cells: Process and Device TCAD Simulation Study

Improving the efficiency of a GaInP solar cell using an AlGaAs buffer layer by optimizing the thicknesses of the PN junction

Novel Simulation and Efficiency Enhancement of Eco-friendly Cu2FeSnS4/c-Silicon Tandem Solar Device

Simulation and optimization of GaAs1-xPx/Si1-yGey/Ge triple junction solar cells

Enhancing Multi-Junction Solar Cell Performance: Advanced Predictive Modeling and Cutting-Edge CIGS Integration Techniques

Designing III-V Multijunction Solar Cells on Silicon

Design and optimization of CdSe-CuSbSe2-based double-junction two-terminal tandem solar cells with VOC> 2.0 V and PCE over 42%

Optical Design of Monolithic Two-Terminal Perovskite/Si Tandem Solar Cells for Efficient Photon Management

TCAD-Based Design and Optimization of Flexible Organic/Si Tandem Solar Cells

III-Nitride/Si Tandem Solar Cell for High Spectral Response: Key Attributes of Auto-tunneling Mechanisms