Abstract:Solar cells have attracted much attention since they can convert solar energy directly into electricity, and have been widely utilized in manufacturing industry and people's daily life. Although the power conversion efficiency (PCE) of single-junction solar cells has gradually improved in recent years, its maximum efficiency is restricted by the Shockley-Queisser (SQ) limit of single-junction solar cells. To exceed the SQ limit and further obtain high efficiency solar cells, researchers have proposed the concept of tandem solar cells. In this work, a systematic theoretical study of chalcopyrite CuGaSe 2 /CuInSe 2 tandem solar cells was carried out by combining first-principle calculations and SCAPS-1D device simulations. Firstly, the electronic structure, defect properties and corresponding macroscopic performance parameters of CuGaSe 2 (CGS) were obtained by first-principles calculations, which were adopted as input parameters for subsequent device simulations of CGS solar cells. Subsequently, the simulations of single-junction CGS and CuInSe 2 (CIS) solar cells were carried out using SCAPS-1D software, respectively. The simulation results for the single junction CIS solar cells are in good agreement with the experimental values. For single-junction CGS cells, the device simulations revealed that CGS single-junction solar cells had the highest short-circuit current (J sc ) and PCE at the growth condition of Cu-rich, Ga-rich and Se-poor chemical growth condition. Further optimization found that the open-circuit voltage (V oc ) and PCE of CGS solar cells can be improved by replacing the electron transport layer (ETL) with ZnSe after the devices with the highest short-circuit current (J sc ). Finally, after the optimized CGS and CIS solar cells were connected in series with two-terminal (2T) monolithic tandem solar cell, the device simulation results show that under the growth temperature of 700 K and the growth environment of Cu-rich, Ga-rich, and Se-poor, with ZnSe as the ETL, the CGS thickness of 2000 nm and the CIS thickness of 1336 nm, the PCE of 2T monolithic CGS/CIS tandem solar cell can reach 28.91 %, which is higher than the recorded efficiency of the current single-junction solar cells, and shows a good application prospect.

Novel Simulation and Efficiency Enhancement of Eco-friendly Cu2FeSnS4/c-Silicon Tandem Solar Device

RESEARCH ON 400cm2 a-Si/a-Si TANDEM SOLAR CELLS

Perovskite/Colloidal Quantum Dot Tandem Solar Cells: Theoretical Modeling and Monolithic Structure

Comprehensive Design and Analysis of Thin Film Sb2S3/CIGS Tandem Solar Cell: TCAD Simulation Approach

Design and analysis of Sb2S3/Si thin film tandem solar cell

Electrical and Optical Investigation of 2T–Perovskite/u-CIGS Tandem Solar Cells With ~30% Efficiency

TCAD-Based Design and Optimization of Flexible Organic/Si Tandem Solar Cells

Design and optimization of CdSe-CuSbSe2-based double-junction two-terminal tandem solar cells with VOC> 2.0 V and PCE over 42%

Design and performance investigation of CIGS/SWCNT tandem solar cell for efficiency improvement

Efficiency Boosting of 4-T Bifacial Dual-Textured Perovskite/Perl Silicon Tandem Solar Cells: Process and Device TCAD Simulation Study

Top cell design and optimization of all-chalcopyrite CuGaSe 2 /CuInSe 2 two-terminal tandem solar cells: first-principles calculations and device simulations

RbGeI3/CuZnSnSSe/CuInGaSe/CdS tandem solar cell with improved performance and lowered cost

Simulation studies of CZT(S,Se) single and tandem junction solar cells towards possibilities for higher efficiencies up to 22%

Modeling of a Tandem Solar Cell Structure Based on CZTS and CZTSe Absorber Materials

Proposal and Design of Organic/CIGS Tandem Solar Cell: Unveiling Optoelectronic Approaches for Enhanced Photovoltaic Performance

Design and Simulation of a‐Si:H/PbS Colloidal Quantum Dots Monolithic Tandem Solar Cell for 12% Efficiency

Investigation of High-Efficiency and Stable Carbon-Perovskite/Silicon and Carbon-Perovskite/CIGS-GeTe Tandem Solar Cells

Device Simulation of Quasi-Two-dimensional Perovskite/silicon Tandem Solar Cells Towards 30%-Efficiency

Maximizing efficiency: Numerical modeling and optimization of 2-terminal perovskite/silicon tandem devices with different bottom cell structures

Simulation of the Efficiency of CdS/CdTe Tandem Multi-Junction Solar Cells

Optimization of all-polymer/Sb2Se3 tandem solar cells for enhanced efficiency: a comprehensive TCAD modeling approach