Abstract:Nickel-based superalloys exhibit pronounced elastic anisotropy and, hence, the local grain orientation strongly affects the stress and strain distribution in the material under mechanical loadings. Therefore, the crack initiation and failure behaviour of components made from nickel-based superalloys are complex and hardly predictable. A better fundamental understanding of the phenomena that occur in nickel-based superalloys under a quasistatic and cyclic load is therefore desired. Previously, a continuum mechanics-based model has been successfully developed, considering the grain structure, the elastic anisotropy, and the Schmid factor, based on data from electron backscatter diffraction (EBSD). The E·m model was confirmed by the finite element method (FEM) simulations and experimental observations regarding the resulting average stresses and strains in the individual grains as well as the formation of slip bands under a quasistatic load with few restrictions. The behaviour under cyclic loadings has been investigated in this work to correlate the mechanical behaviour, simulated by the previously developed FE models, with the local stiffness and Schmid factors considering fatigue failure. For this purpose, the fatigue behaviour of Inconel 617 samples was characterised up to the high-cycle fatigue (HCF) regime, accompanied by EBSD measurements for stress amplitudes that resulted in strains close to the elastic–plastic regime. The EBSD data were used to create digital twins of the samples to simulate the mechanical reaction to a displacement similar to the associated strain of the fatigue tests. An analysis of the fractured samples by scanning electron microscopy was performed to retrace the location of the crack initiation supported by the EBSD measurements before and after fatigue testing. Two samples were investigated in detail that showed different fracture types. Sample 1 showed transcrystalline failure in a grain that showed a high Young's modulus, Schmid factor, and resolved shear stress that indicates a failure due to the properties of the grain itself. In contrast, an intercrystalline failure was observed for sample 2 that showed large differences in the orientation and, hence, largely different mechanical properties in the area of failure as well. The observed failure types, the resulting stresses and strains calculated by the FE model, and the consideration of the E·m model showed an agreement of all the methods. Therefore, the findings of this work complement previous investigations of the mechanical behaviour of coarse-grained anisotropic nickel-based superalloys with a focus on the orientations of the grains towards the loading direction.

Relation Between Striations Spacing and Fatigue Crack Growth Rates for Additive Manufactured Inconel 625

High- and low-cycle-fatigue properties of additively manufactured Inconel 625

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

Effect of Internal Defects on the Fatigue Behavior of Additive Manufactured Metal Components: A Comparison between Ti6Al4V and Inconel 718

Role of defects and microstructure on the fatigue durability of Inconel 718 obtained by additive layer manufacturing route

Striation lines in intermittent fatigue crack growth in an Al alloy

Fatigue Assessment of Inconel 625 Produced by Directed Energy Deposition from Miniaturized Specimens

Experimental and Modeling Study on Small Fatigue Crack Initiation and Propagation Behavior of Inconel 617

The low cycle fatigue property, damage mechanism, and life prediction of additively manufactured Inconel 625: Influence of temperature

Exploring the role of Type-II residual stresses in a laser powder bed fusion nickel-based superalloy using measurement and modeling

Microstructure evolution, failure mechanism and life prediction of additively manufactured Inconel 625 superalloy with comparable low cycle fatigue performance

Fatigue assessment of as‐built and heat‐treated Inconel 718 specimens produced by additive manufacturing including notch effects

Fatigue Analysis of the Nickel-Based Superalloy Inconel 617 by Fatigue Experiments and EBSD Data-Based Finite Element Simulations in Correlation with E·m Theories

Studies of High-Temperature Fatigue Behavior and Mechanism for Nickel-Based Superalloy Inconel 625

Fatigue crack growth behavior in an aluminum alloy Al–Mg–0.3Sc produced by wire based directed energy deposition process

Multi-stage dwell fatigue crack growth behaviors in a nickel-based superalloy at elevated temperature

Cyclic microstructure analysis, crack propagation and life prediction of Inconel 750H considering the slip fracture energy

Fatigue analysis of selective laser melting Inconel 718 and the mechanism of ductile–brittle continuous alternating steps during fatigue process

Fatigue and Fracture Behavior of Nickel-Based Superalloy Inconel 718 Up to the Very High Cycle Regime

A Study of Microstructural Tensile and Fatigue Properties Coupled with Digital Image Correlation of Hybrid Manufactured Inconel 718 Parts by Extrusion and Powder Bed Fusion

Comparison of the continuum damage and fracture mechanics in fatigue assessment of components containing residual stresses