Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Uniaxial‐Stress Driven Performance Enhancement of Multi‐Beam Spark Plasma Sintered BiSbTe/Epoxy Flexible Films

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

Interlayer carrier high-speed conductive channels and excellent electrical transport performance of multilayer films

Carrier concentration and orientation optimization for high performance (Sb,Bi) 2 Te 3 thermoelectric films via magnetron co-sputtering

Realizing High‐Performance BiSbTe Magnetic Flexible Films via Acceleration Movement and Hopping Migration of Carriers

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Thermoelectric Performance Enhancement in BiSbTe Alloy by Microstructure Modulation via Cyclic Spark Plasma Sintering with Liquid Phase

Enhancing Thermoelectric and Cooling Performance of Bi 0.5 Sb 1.5 Te 3 through Ferroelectric Polarization in Flexible Ag/PZT/PVDF/Bi 0.5 Sb 1.5 Te 3 Film

Tuning Thermoelectric Conversion Performance of BiSbTe/Epoxy Flexible Films with Dot Magnetic Arrays

Direct Melt-Calendaring of Highly Textured (Bi,Sb)2Te3 Thick Films: Superior Thermoelectric and Mechanical Performance via Strain Engineering

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Effect of spark plasma sintering temperature on thermoelectric properties of Bi 2 S 3 polycrystal

High thermoelectric performance achieved in Bi0.4Sb1.6Te3 films with high (00l) orientation via magnetron sputtering

Optimizing the thermoelectric properties of flexible Bi[math]Sb[math]Te[math] thin films via modulating magnetron sputtering power

Enhancement of thermoelectric performance in Mg 3 (Sb,Bi) 2 through engineered lattice strain and controlled carrier scattering

Modulation of Vacancy Defects and Texture for High Performance n‐Type Bi2Te3 via High Energy Refinement

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Enhanced electrical and mechanical properties of Bi2Te3-based thermoelectric thick films enabled by a practical dynamic regulation strategy

Enhanced Thermoelectric Performance of N-Type Bi2Te2.7Se0.3 Via a Simple Liquid-Assisted Shear Exfoliation

Simultaneous Enhancement of the Thermoelectric and Mechanical Performance in One-Step Sintered n-Type Bi2Te3-Based Alloys via a Facile MgB2 Doping Strategy

High Thermoelectric Performance of p-Type Bi0.4Sb1.6Te3+ x Synthesized by Plasma-Assisted Ball Milling