Abstract:Zirconia composite ceramic materials are popular for their many excellent properties. In this study, nTi-3Y–ZrO 2 composite ceramics were produced by the mechanical alloying-microwave sintering method with different Ti-doping amounts and microwave sintering temperatures. The sample's phase composition, stability rate, lattice parameters, micromorphology, relative density, and grain size are characterized. The results showed that when the sintering temperature is 1200 °C, the samples with different doping amounts are mainly mixed crystalline structures with tetragonal and cubic phases, and the stability rate remains above 90 %. As TiO 2 doping increases, the lattice parameters a(Å) and b(Å)first increase and then decrease, while the lattice parameter c (Å) shows an overall increasing trend. Raman data demonstrated that the increase in Ti content promoted the generation of tetragonal phase zirconia. The average grain size is 61.33 nm, 76.23 nm, 58.77 nm, 63.35 nm, and 68.99 nm, respectively. The increase in doping is also accompanied by a narrowing of the grain size distribution, which increases the sintering activity of the sample. In addition, the relative densities of the samples were 67.85 %, 73.94 %, 84.25 %, 84.87 %, and 77.54 %, respectively, showing a gradual increasing trend overall. When the microwave sintering temperature is 1200 °C, and the doping amount is 5Ti–3Y–92Zr, the performance of the sample is superior to other groups. The preparation of nTi-3Y–ZrO 2 composite ceramics can provide certain ideas for preparing ceramic materials with excellent performance in various aspects.

The microstructural evolution and densification process of titanium or tin doped indium zinc oxide ceramic targets

Preparation of extraordinary high-density indium-tin oxide target on the basis of pressure-less sintering method

Sintering behavior of IZO ceramic targets prepared using hydrothermally synthesized Zn-doped In2O3 nanoparticles

Achieving high relative density and low resistivity in indium tin oxide targets via Bi2O3-CeO2 additive

The experimental investigation on preparation of Li-doped ZnO ceramic targets and sputtering thin films

Effects of Al2O3 doping on the microstructural evolution and densification process of AZO targets

Microstructure and Microwave Dielectric Properties of Ni Doped Zinc Borate Ceramics for LTCC Applications

Structural, Morphological and Optical Characterization of Tin Doped Zinc Oxide Thin Film by (SPT)

Microstructure and Microwave Dielectric Properties of Tio2-Doped Zn2sio4 Ceramics Synthesized Through the Sol-Gel Process

The Effect of Zirconium Doping on Solution-Processed Indium Oxide Thin Films Measured by a Novel Nondestructive Testing Method (microwave Photoconductivity Decay)

Novel sintering and band gap engineering of ZnTiO3 ceramics with excellent microwave dielectric properties

Microstructure, Phase Evolution and Interfacial Effects in a New Zn0.9Mg0.1TiO3-ZnNb2O6 Ceramic System with Greatly Induced Improvement in Microwave Dielectric Properties

Microstructure and Broadband Dielectric Properties of Zn2SiO4 Ceramics with Nano-Sized TiO2 Addition

Characterization Studies of the Structure and Properties of Zr-doped SnO2 Thin Films by Spin-Coating Technique

The Effect of TiO2 on the Dielectric Performance of ZrO2 and Nb2O5 Pre-Doped CaCu3Ti4O12 Ceramics

Effect of power density on compositional and structural evolution of ITO thin film by HiPIMS method

Preparation of novel Ti–Y/ZrO 2 ceramic by two-step of mechanical alloying and microwave-assisted sintering process

Li-Doped Zno Ceramic Target Preparation And Rf Magnetron Sputtering Zno Films

Effects of Ti-Doped Concentration on the Microstructures and Optical Properties of Zno Thin Films

Relationships between dopants, microstructure and the microwave dielectric properties of ZrO2-TiO2-SnO2 ceramics

Study on the preparation and the film-forming properties of Mo-and Al-doped ZnO ceramic targets