Abstract:Al alloy joints soldered with Sn-based filler metal are susceptible to corrosion and early failure when exposed to moisture, resulting in severe accidents and substantial economic losses. This study proposes a method to prevent galvanic corrosion by separating Al alloys and Sn-based filler metals with an insulating barrier layer of anodized aluminum oxide (AAO) composed of Al2O3. The successful joining of anodized aluminum alloy (AAA) with Sn-9Zn-2Al was achieved through ultrasonic-assisted hot dipping and soldering in air at 240 degrees C. Microstructural examination revealed strong bonding between the solder alloy and AAO, with the solder infiltrating the AAO nanotubes and a transition layer consisting of two sublayers at the interface: amorphous ZnO mixed with nanocrystals (ZnO and Al2O3) and amorphous Al2O3. The shear strength of the joints ranged from 31.8 to 32.8 MPa when subjected to ultrasonic hot dipping for 0.5-2.0 s, with no significant difference observed. Fracture initiation and propagation occur within the transition layer at the interface. The shear strength of joints subjected to dipping for more than 3.0 s decreased slightly to 27.9 MPa due to localized peeling off of AAO from the Al substrate. The formation of the interface involves the segregation of Al and Zn on the liquid filler metal surface, driven by differences in atomic activity. Due to the jet force from cavitation, an Al-rich liquid infiltrates the nanotube, resulting in the formation of Zn-O at the interface and Al-O both at the interface and within the nanotube. Throughout this process, the wetting model shifts from a Cassie state to a near-Wenzel state. Immersion tests of two types of joints, Al/SnZnAl/Al and AAA/SnZnAl/AAA, confirmed that galvanic corrosion of Sn/Al was completely inhibited by the latter. Consequently, AAA joints demonstrate excellent corrosion resistance, validating this approach as a promising solution to the Al/Sn galvanic corrosion issue.

Manufacturing high-strength and corrosion-resistant 6063Al joints by an ultrasonic-assisted liquid and solid phase diffusion technology

Improve mechanical properties and corrosion resistance of Al/Sn heterogeneous joints by ultrasonic-assisted liquid phase diffusion bonding

High-strength joining of 6063Al alloys by an Zn–Sn hypereutectic interlayer in air based on liquid and solid phase diffusion

Ultrasonic-assisted liquid phase diffusion bonding of Al alloys under low temperature and pressure for high-temperature resistance applications

Interfacial Structure and Properties of Anodized 6061 Al Alloy Joints by Ultrasonic-Assisted Hot Dipping and Soldering Using a Sn-9Zn-2Al Filler Metal

A Novel Diffusion Bonding of 6063al Based on a Mode of Diffusion-Migrating and Suspension-Broken of Surface Oxide Film

Abnormal Rapidly Homogenized Joining of Aluminum Alloys Through a Cross-Scale Diffusion

Ultrasonic-assisted Soldering of Fine-Grained 7034 Aluminum Alloys Using ZnAl Filler Metals

Ultrasonic-assisted Soldering of Fine-Grained 7034 Aluminum Alloy Using Sn-Zn Solders below 300°C.

Mechanism of ultrasonic-assisted transient liquid phase bonding of 6061 Al alloy with cladded Zn-Al alloy in air

Ultrasonic-promoted Rapid TLP Bonding of Fine-Grained 7034 High Strength Aluminum Alloys.

Si Particulate-Reinforced ZnAl Based Composites Joints of Hypereutectic Al50Si Alloys by Ultrasonic-Assisted Soldering

Joining mechanism, microstructure, and mechanical properties of AZ31/6061 joint prepared by pouring fusion welding process assisted with Zn-xSn brazing filler

Joining Mg Alloys with Zn Interlayer by Novel Ultrasonic-Assisted Transient Liquid Phase Bonding Method in Air

Microstructure Evolution and Mechanical Properties of Ultrasonic-Assisted Soldering Joints of 2024 Aluminum Alloys

Rapid Ultrasound-Induced Transient-Liquid-phase Bonding of Al-50Si Alloys with Zn Interlayer in Air for Electrical Packaging Application

Joining of Magnesium and Aluminum Via Arc-Assisted Ultrasonic Seam Welding with Sn/Zn Composite Interlayer

Microstructure and Mechanical Performance of AZ31/2024 Dissimilar Alloy Joints Using a Multi-Interlayer of Ni/Al/Zn Via Ultrasonic-Assisted Transient Liquid Phase Bonding

Deformation-free Manufacturing Al Alloy Laminated Structures by an Ultrasonic-Assisted Diffusion Bonding

Ultrasonic Soldering Aluminum at Low Temperature

Ultrarapid Formation of Multi -Phase Reinforced Joints of Hypereutectic Al-Si Alloys Via an Ultrasound-Induced Liquid Phase Method Using Sn-51In Interlayer