Abstract:This paper attempts to present a brief review of recent progress obtained by the author's group in the research area of ion beam metallurgy, namely (i) formation of metal-nitride by nitrogen implantation; (ii) metallic glass formation by ion mixing; and (iii) icosahedral phase formation by ion mixing. Silver- and copper-trinitrides have been formed, for the first time, by RT 80 keV nitrogen ion implantation for doses up to 2×10 18 N cm −2 . These indicated that deposition of large amounts of energy during implantation could provide the reaction energy of noble-metal-nitride with rather positive heat of formation, and that local nitrogen concentration in the implanted films could be considerably greater than that limited by the sputtering yield involved. Besides, our observation of the reverse sequence of phase transition TiTiNTi 2 N with increasing nitrogen dose suggested that growth kinetics (or structural compatibility between newly formed phase and the matrix) might be a key factor in determining the nitride formation in some systems. Two parameters were found of importance in influencing the glass forming ability (GFA) of binary metal systems. One is MPAR (maximum possible amorphization range), which equals 100% minus the maximum solid solubilities observed in the equilibrium phase diagram. The other is the heat of formation. A map was constructed by these parameters and some empirical qualifications were found to classify the systems according to GFA into three categories of Hardly (HGF), Possible (PGF) and Readily (RGF) Glass Forming systems. The FeCu system is an immiscible one, in which amorphization induced by ion mixing could only occur within a narrow composition range. The favored composition was figured out experimentally, and an icosahedral phase was also formed by ion mixing without post-annealing at corresponding atomic stoichiometry. Interestingly, a similar phase was also formed in the FeMo system.

A new mechanism of surface phase formation on precipitation-hardening alloy under ion irradiation

Early Stages of Precipitation in Γ' Phase of a Ni–Al–Ti Model Alloy: Phase-Field and First-Principles Study

Atomic-scale computer simulation of mixture precipitation mechanism for Ni75AlxV25-x alloy

Surface Modification of Ni3al-Based Alloy Ic6 with Intense Pulsed Ion Beams

Accelerated Precipitation and Growth of Phases in an Al-Zn-Mg-Cu Alloy Processed by Surface Abrasion

Nanoscale Icosahedral Quasicrystal Phase Precipitation Mechanism During Annealing for Mg–Zn–Gd-based Alloys

The growth mechanisms of θ′ precipitate phase in an Al-Cu alloy during aging treatment

Insights into precipitation characteristics and strengthening mechanisms in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy

Formation mechanism of an α2 phase-rich layer on the surface of Ti-22Al-25Nb alloy

Exceptional Surface Modifications of a Biodegradable Zn-Li-Cu Alloy in Electrolytes and under Ga-ion-beam Milling

Surface Growth, Inner Defects and Interface Mixing of the Cr Coating on Zr Alloy Irradiated by 5 Mev Protons at 400 °C

Ion Irradiation Induced Nanocrystal Formation in Amorphous Zr55cu30al10ni5 Alloy

Ion Bombardment Induced Surface Microstructural Modification of Aluminum Alloy

In situ observation of surface morphology evolution in tungsten under focused Ga + ion irradiation

Study Of Alloy Phase Formation Using Ion-Beams

Phase transformation from phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

Effect Of Irradiation With Intense Pulsed Ion Beams On The Phase Evolution Of Ni3al Based Superalloy Ic6

Surface modification and structure evolution of aluminum under argon ion bombardment

Inclined θ′ precipitates with terraced Cu/Mn-rich multilayers in Al–Cu alloys

Observations of Percolation Structures Induced in Thin Solid Films by Ion Irradiation

Atomic-scale investigation of the heterogeneous precipitation in the E (Al18Mg3Cr2) dispersoid of 7075 aluminum alloy