Abstract:Ultrasound-assisted grinding is a new method for compound precision machining of C/SiC with excellent machining characteristics. The electroplated diamond grinding head performs a two-dimensional ultrasonic auxiliary plane grinding single-factor experiment for SiC, 2.5D-C/SiC, and chopped fiber-C/SiC. The influences of linear speed, feed speed, grinding depth, fiber orientation, and fiber structure on the grinding force and surface quality are analyzed in this study. The surface formation and removal mechanisms of C/SiC composites are discussed. The results show that within the parameters of this experiment, the grinding force and surface roughness decrease with the increase in linear speed and increase with the increase in feed speed and grinding depth. The grinding force and roughness can be significantly reduced by applying two-dimensional ultrasound. The maximum percentage reduction in normal and tangential grinding forces was 26.79% and 31.69% when grinding 2.5D-C/SiC along 90° fiber orientation. The maximum percentage of surface roughness reduction was 37.93% when 2.5D-C/SiC was ground along a 90° fiber orientation. The influence of fiber orientation on the two types of C/SiC grinding force is the same, and both are satisfied that the grinding force is highest in the 45° fiber orientation, second highest in the 90° fiber orientation, and lowest in the 0° fiber orientation. The effect of fiber orientation on the roughness of 2.5D-C/SiC is as follows: the surface roughness is highest at 45° fiber orientation, second highest at 90° fiber orientation, and lowest at 0° fiber orientation. The effect of fiber orientation on the roughness of short-cut fiber-C/SiC is as follows: the surface roughness is highest at 0° fiber orientation, second highest at 45° fiber orientation, and lowest at 90° fiber orientation. The effect of fiber structure on grinding force is as follows: Under the same machining conditions, the grinding forces are highest on SiC, second highest on short-cut fiber-C/SiC, and lowest on 2.5D-C/SiC. The effect of fiber structure on surface roughness is as follows: Under the same machining conditions, the surface roughness is highest on short-cut fiber-C/SiC, second highest on 2.5D-C/SiC, and lowest on SiC.

Wear-induced variation of surface roughness in grinding 2.5D C f /SiC composites

Wear-induced Variation of Surface Roughness in Grinding 2.5D Cf/SiC Composites

Some observations in grinding surface quality of FRCMC

Grinding Characteristics and Surface Roughness Modeling of 2.5D Woven SiCf/SiC Ceramic Matrix Composites

Grindability and surface quality of SiCp/Al composites with resin bond and electroplated wheels

Enhancing Ductile Removal of Cf/SiC Composites During Abrasive Belt Grinding Using Low-Hardness Rubber Contact Wheels

Research on micro-grinding performance of 2.5D Cf/SiC composites

Simulated and Measured Surface Roughness in High-Speed Grinding of Silicon Carbide Wafers

Material removal behavior of C<sub>f</sub>/SiC ceramic matrix composites as a function of abrasive wear during diamond abrasive belt grinding

Experimental study on grinding 2.5D C/SiC composites by electroplated grinding wheel with ordered abrasive clusters

Surface Roughness Model of Ground 4H-SiC Considering Ductile and Brittle Removal

Numerical Investigation on the Influence of Cutting-Edge Radius and Grinding Wheel Speed on Chip Formation in SiC Grinding

Study on the Surface Generation Mechanism During Ultra-Precision Parallel Grinding of SiC Ceramics

Study on micro-grinding mechanism and surface quality of hardened 20 vol% SiCp/Al composites

The Influence of Grain Geometry and Wear Conditions on the Material Removal Mechanism in Silicon Carbide Grinding with Single Grain

Effect of tool wear on machining quality in milling C f /SiC composites with PCD tool

Numerical simulation of single abrasive grain grinding of silicon carbide surface

Study on removal mechanism and surface quality of grinding carbon fiber toughened ceramic matrix composite

Grinding mechanism and surface quality evaluation strategy of single crystal 4H-SiC

Experimental study of the removal characteristics of C/SiC with different fiber structure arrangements for two-dimensional ultrasound-assisted grinding

Mechanism analysis and process optimization of nanogrinding single-crystal SiC