Abstract:Experimental, analytical and numerical methods have been employed to study the aerodynamic performance of four different cooled tips with coolant mass ratios between zero and 1.2% at three tip gaps of 1%, 1.6% and 2.2% of the chord. The four cooled tips are two flat tips with different coolant holes, a cooled suction side squealer tip and a cooled cavity tip. Each tip has ten coolant holes with the same diameter.The uncooled cavity tip produces the smallest loss among all uncooled tips. On the cooled flat tip, the coolant is injected normally into the tip gap and mixes directly with flow inside the tip gap. The momentum exchange between the coolant and the flow that enters the tip gap creates significant blockage. As the coolant mass flow ratio increases, the tip leakage loss of the cooled flat tip first decreases and then increases. For the cooled cavity tip, the blockage effect of the coolant is not as big as that on the cooled flat tip. This is because after the coolant exits the coolant holes, it mixes with flow in the cavity first, and then mixes with tip flow in the tip gap. The tip leakage loss of the cooled cavity tip increases as the coolant mass flow ratio increase. As a result, at a tip gap of 1.6% of the chord, the cooled cavity tip gives the lowest loss.At the smallest tip gap of 1% of the chord, the cooled flat tip produces less loss than the cooled cavity tip when the coolant mass flow ratios larger than 0.23%. This is because with the same coolant mass flow ratio, a proportionally larger blockage is created at the smallest tip gap. At the largest tip gap of 2.2% of the chord, the cavity tip achieves the best aerodynamic performance. This is because, the effect of the coolant is reduced and the benefits of the cavity tip geometry dominate. At a coolant mass flow ratio of 0.55%, the cooled flat tips produce a lower loss than the cavity tip at tip gaps less than 1.3% of the chord. The cooled cavity tip produces the least loss for tip gaps larger than 1.3% of the chord. The cooled suction side squealer has the worst aerodynamic performance for all tip gaps studied.

Aerothermal characteristics evaluation for different tip configurations without and with film cooling on transonic turbine

An Experimental Investigation of Adiabatic Film Cooling Effectiveness and Heat Transfer Coefficient on a Transonic Squealer Tip

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

An Investigation on Film Cooling and Aerodynamic Performance of Squealer Blade Tip with Inclined Cavity Bottom

Influence of Film Hole Arrangement on Cooling and Aerodynamic Performance of Blade Tip with Squealer Structure

Investigation of the film-cooling and flow characteristics of trapezoidal slot scheme on the blade tip with partial pressure side squealer in transonic flow

Experimental and Numerical Investigations into the Blade Tip Phantom Cooling Performance

Effects of Rotor Squealer Tip with Non-Uniform Heights on Heat Transfer Characteristic and Flow Structure of Turbine Stage

Heat Transfer Coefficient and Film Cooling Effectiveness on the Partial Cavity Tip of a Gas Turbine Blade

Experimental and Computational Assessment into the Heat Transfer for the Blade Multicavity Tips

The Tip Leakage Flow of an Unshrouded High Pressure Turbine Blade with Tip Cooling

Investigation on film cooling and aerodynamic performance of blade tip with tangential jet cooling scheme at transonic flow

Experimental and Numerical Evaluation of the Film Cooling Characteristics of the Multi-cavity Tip with Inclined Film Holes

Aerothermal Optimization of Turbine Cascade Squealer Tip with Non-Uniform Squealer Height

Thermal Performance of Transonic Cooled Tips in a Turbine Cascade

Comparisons of blade tip phantom cooling effectiveness for two tip structures with three tip clearances

Unsteady numerical study of film cooling and heat transfer on turbine blade squealer tip with coolant jet

An aerothermal analysis of the effects of tip gap height and cavity depth of a gas turbine blade

Experimental Comparisons of Film Cooling Performance for the Multi-Cavity Tips at Two Different Tip Gaps

Effects of Squealer Tip Geometry Deviation on Flow Field and Aerodynamic Performance Using Uncertainty Quantification Method and Sensitivity Analysis Method

Cooling layout optimization for a turbine blade squealer tip with the application of oval holes