Abstract:A numerical investigation of the flow and heat transfer characteristics of tip leakage in a typical film cooled industrial gas turbine rotor is presented in this paper. The computations were performed on a rotating domain of a single blade with a clearance gap of 1.28% chord in an engine environment. This standard blade featured two coolant and two dust holes, in a cavity-type tip with a central rib. The computations were performed using CFX 5.6, which was validated for similar flow situations by Krishnababu et al. (2007, “Aero-Thermal Investigation of Tip Leakage Flow in Axial Flow Turbines: Part I—Effect of Tip Geometry,” ASME Paper No. 2007-GT-27954). These predictions were further verified by comparing the flow and heat transfer characteristics computed in the absence of coolant ejection with computations previously performed in the company (SIEMENS) using standard in-house codes. Turbulence was modeled using the shear-stress transport (SST) k-ω turbulence model. The comparison of calculations performed with and without coolant ejection has shown that the coolant flow partially blocks the tip gap, resulting in a reduction in the amount of mainstream leakage flow. The calculations identified that the main detrimental heat transfer issues were caused by impingement of the hot leakage flow onto the tip. Hence three different modifications (referred as Cases 1–3) were made to the standard blade tip in an attempt to reduce the tip gap exit mass flow and the associated impingement heat transfer. The improvements and limitations of the modified geometries, in terms of tip gap exit mass flow, total area of the tip affected by the hot flow and the total heat flux to the tip, are discussed. The main feature of the Case 1 geometry is the removal of the rib, and this modification was found to effectively reduce both the total area affected by the hot leakage flow and total heat flux to the tip, while maintaining the same leakage mass flow as the standard blade. Case 2 featured a rearrangement of the dust holes in the tip, which, in terms of aerothermal dynamics, proved to be marginally inferior to Case 1. Case 3, which essentially created a suction-side squealer geometry, was found to be inferior even to the standard cavity-tip blade. It was also found that the hot spots, which occur in the leading edge region of the standard tip, and all modifications contributed significantly to the area affected by the hot tip leakage flow and the total heat flux.

An aerothermal analysis of the effects of tip gap height and cavity depth of a gas turbine blade

Aerothermal performance of cavity tip with flow structure effects in a transonic high-pressure turbine blade

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

Squealer Geometry Effects on Aerothermal Performance of Tip-Leakage Flow of Cavity Tips

Effects of Squealer Tip Geometry Deviation on Flow Field and Aerodynamic Performance Using Uncertainty Quantification Method and Sensitivity Analysis Method

Heat Transfer Coefficient and Film Cooling Effectiveness on the Partial Cavity Tip of a Gas Turbine Blade

The Tip Leakage Flow of an Unshrouded High Pressure Turbine Blade with Tip Cooling

Influence of Film Hole Arrangement on Cooling and Aerodynamic Performance of Blade Tip with Squealer Structure

An Investigation on Film Cooling and Aerodynamic Performance of Squealer Blade Tip with Inclined Cavity Bottom

Unsteady numerical study of film cooling and heat transfer on turbine blade squealer tip with coolant jet

Aero-Thermal Investigation of Tip Leakage Flow in a Film Cooled Industrial Turbine Rotor

Aerothermal Investigation of Tip Leakage Flow in a Film Cooled Industrial Turbine Rotor

Experimental Comparisons of Film Cooling Performance for the Multi-Cavity Tips at Two Different Tip Gaps

Effects of the circumferential casing groove configuration on aerothermal performance of a transonic turbine stage

Investigation into the Film Cooling Performance of Multi-Cavity Tips with Different Cavity Depths

Numerical Study on Vortex Structures and Loss Characteristics in a Transonic Turbine with Various Squealer Tips

Aerothermal Effects of Squealer Openings on a Cavity Tip in a Turbine Cascade

INFLUENCES OF DEPTH AND RIM WIDTH OF SQUEALER TIP ON THE LEAKAGE FLOW AND HEAT TRANSFER

Experimental and Numerical Investigations into the Blade Tip Phantom Cooling Performance

Cooling layout optimization for a turbine blade squealer tip with the application of oval holes

Tip Gap Size Effects on Thermal Performance of Cavity-Winglet Tips in Transonic Turbine Cascade with Endwall Motion