Abstract:Experimental, analytical and numerical methods have been employed to study the aerodynamic performance of four different cooled tips with coolant mass ratios between zero and 1.2% at three tip gaps of 1%, 1.6% and 2.2% of the chord. The four cooled tips are two flat tips with different coolant holes, a cooled suction side squealer tip and a cooled cavity tip. Each tip has ten coolant holes with the same diameter.The uncooled cavity tip produces the smallest loss among all uncooled tips. On the cooled flat tip, the coolant is injected normally into the tip gap and mixes directly with flow inside the tip gap. The momentum exchange between the coolant and the flow that enters the tip gap creates significant blockage. As the coolant mass flow ratio increases, the tip leakage loss of the cooled flat tip first decreases and then increases. For the cooled cavity tip, the blockage effect of the coolant is not as big as that on the cooled flat tip. This is because after the coolant exits the coolant holes, it mixes with flow in the cavity first, and then mixes with tip flow in the tip gap. The tip leakage loss of the cooled cavity tip increases as the coolant mass flow ratio increase. As a result, at a tip gap of 1.6% of the chord, the cooled cavity tip gives the lowest loss.At the smallest tip gap of 1% of the chord, the cooled flat tip produces less loss than the cooled cavity tip when the coolant mass flow ratios larger than 0.23%. This is because with the same coolant mass flow ratio, a proportionally larger blockage is created at the smallest tip gap. At the largest tip gap of 2.2% of the chord, the cavity tip achieves the best aerodynamic performance. This is because, the effect of the coolant is reduced and the benefits of the cavity tip geometry dominate. At a coolant mass flow ratio of 0.55%, the cooled flat tips produce a lower loss than the cavity tip at tip gaps less than 1.3% of the chord. The cooled cavity tip produces the least loss for tip gaps larger than 1.3% of the chord. The cooled suction side squealer has the worst aerodynamic performance for all tip gaps studied.

Aerothermal performance of cavity tip with flow structure effects in a transonic high-pressure turbine blade

Squealer Geometry Effects on Aerothermal Performance of Tip-Leakage Flow of Cavity Tips

An aerothermal analysis of the effects of tip gap height and cavity depth of a gas turbine blade

Numerical Study on Vortex Structures and Loss Characteristics in a Transonic Turbine with Various Squealer Tips

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

Effects of Squealer Tip Geometry Deviation on Flow Field and Aerodynamic Performance Using Uncertainty Quantification Method and Sensitivity Analysis Method

Effects of Rotor Squealer Tip with Non-Uniform Heights on Heat Transfer Characteristic and Flow Structure of Turbine Stage

Aerothermal Optimization of Turbine Cascade Squealer Tip with Non-Uniform Squealer Height

Aerothermal Effects of Squealer Openings on a Cavity Tip in a Turbine Cascade

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

The Tip Leakage Flow of an Unshrouded High Pressure Turbine Blade with Tip Cooling

Effects of Endwall Motion on Thermal Performance of Cavity Tips with Different Squealer Width and Height

Aerothermal Performance of Different Tips in Transonic Turbine Cascade with End-Wall Motion

Computational Study Of The Thermal Performance Of An Unshrouded High Pressure Turbine Blade Tip

Aerodynamic performance of tip leakage flow of two different blade tips in transonic turbine

Effects of the circumferential casing groove configuration on aerothermal performance of a transonic turbine stage

Heat Transfer Coefficient and Film Cooling Effectiveness on the Partial Cavity Tip of a Gas Turbine Blade

Development of a tip leakage loss model for high-pressure turbines with squealer tips based on physics-driven and data-driven methods

Optimization of Rotor Tip Cavity Shapes for Mitigating Aerodynamic Tip Leakage Losses

Tip Gap Size Effects on Thermal Performance of Cavity-Winglet Tips in Transonic Turbine Cascade with Endwall Motion

An Investigation on Film Cooling and Aerodynamic Performance of Squealer Blade Tip with Inclined Cavity Bottom