Abstract:This study explores the impact of fluorine (F) erosion on the tungsten (W) gate process and proposes measures to mitigate the word line (WL) leakage resulting from F erosion in 3D NAND flash memory. As the number of layers in 3D NAND increases, the tungsten (W) gate word line (WL) layer fill process becomes more challenging during the post-gate process. As the fill path length increases, the tungsten gates become more susceptible to voiding during deposition, resulting in the accumulation of fluorine (F) by-products, and causing fluorine attack issues. In particular, under the influence of subsequent high-temperature processes, the by-products containing fluorine can diffuse into the surrounding structure and corrode the surrounding oxide layer. This leads to WL leakage, thereby affecting device yield and reliability. This paper begins by analyzing the microscopic principles of fluorine erosion in 3D NAND. We also propose a low-pressure annealing method to address the issue of fluorine erosion. Then, we conducted annealing experiments on planar thin film stacks and 3D filled structures under both atmospheric and low-pressure conditions. We used various methods to characterize the concentration and distribution of residual fluorine elements. The experimental results demonstrate that residual fluorine elements in the tungsten gate can be effectively discharged by low-pressure annealing under appropriate conditions, thus reducing the leakage index of the word line. Additionally, as the outer CH is closer to the fluorine discharge channel, the impact of low-pressure annealing on the outer CH is more pronounced than on the inner CH. Low-pressure annealing can significantly reduce the fluorine content in the tungsten gate. This method can also mitigate the issue of fluorine attack oxides and decrease WL leakage. Using low-pressure annealing treatment can also enhance the quality of 3D NAND flash technology.

A Case of Plasma-Induced Film Breakdown in 3D NAND BEOL Dielectric Etch

Pre-metal dielectric PE TEOS oxide pitting in 3D NAND: mechanism and solutions

Unveiling Polycrystalline Silicon Channel Dissolution Mechanism in Wet Etching Process of 3d Nand Fabrication

Investigation of shape etching on multi-layer SiO2/poly-Si for 3D NAND architecture

An Optimized Device Structure with Improved Erase Operation within the Indium Gallium Zinc Oxide Channel in Three-Dimensional NAND Flash Applications

Breakdown Voltage of Ultrathin Dielectric Film Subject to Electrostatic Discharge Stress

Optimization of SADP Process for Defect Reduction in Planar 2D NAND Flash

Comprehensive investigations on defects' stability caused lateral charge loss in Ti-doped 3D NAND

A Drain Leakage Phenomenon in Poly Silicon Channel 3D NAND Flash Caused by Conductive Paths along Grain Boundaries

Redeposition Mechanism on Silicon Oxide Layers During Selective Etching Process in 3D NAND Manufacture

Selective Wet Etching Technology in 3D NAND Flash Manufacturing

Improvement of Fluorine Attacking Induced Word-Line Leakage in 3D NAND Flash Memory

Plasma simulation of HF plasma generated in dual-frequency chamber for high aspect ratio dielectric etching

Optimization of Bump Defect at High-Concentration In-Situ Phosphorus Doped Polysilicon/TEOS Oxide Interface for 3D NAND Flash Memory Application

Adaptive Bitline Voltage Countermeasure for Neighbor Wordline Interference in 3D NAND Flash Memory-Based Sensors

Investigation of Endurance Characteristics in 3-D NAND Flash Memory With Trap Profile Analysis

A Novel Channel Preparation Scheme to Optimize Program Disturbance in Three-Dimensional NAND Flash Memory

Analysis of Residual Stresses Induced in the Confined 3D NAND Flash Memory Structure for Process Optimization

The Effect of Different Stress Conditions on MONOS Breakdown for 3D NAND Flash Memory

Plasma Induced Damage Reduction of Ultra Low-k Dielectric by Using Source Pulsed Plasma Etching for Next BEOL Interconnect Manufacturing

Methods of Reducing Metal Damager Defect in Back End of Line for Semiconductor in 28nm Technology