Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Theoretical and experimental study of the microstructure of a metallic melt in an In 50 Bi 50 alloy based on the Wulff cluster model

The Microstructure in an Al–Ti Alloy Melt: The Wulff Cluster Model from a Partial Structure Factor

The structure of metallic melts in eutectic alloys based on the Wulff cluster model: theory meets experiment

Research on microstructure of Ti-6Al-4V titanium alloy by thermal simulation under water cooling

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Molecular Dynamics Computation of the Liquid Structure of Fe50Al50 Alloy

Structural Studies of Clusters in Melt of FeAl Compound

First principles study on the mechanism of abnormal viscosity change of pure Al & Pb melts based on Wulff cluster model

A New Model for Microstructure of Liquid Metals

Modeling and Simulation of the Microstructure Evolution During A Cooling of Immiscible Alloys in the Miscibility Gap

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Experimental Andab Initiomolecular Dynamics Simulation Studies of Liquidal60cu40alloy

Lead-Bismuth Eutectic: Atomic and Micro-Scale Melt Evolution

Observation of Bi Coarsening and Dissolution Behaviors in Melting Al–Bi Immiscible Alloy

Quantitative Multi-Phase-field Modeling of Non-Isothermal Solidification in Hexagonal Multicomponent Alloys

PART 1-Symposium E-Intermetallics & High Temperature Alloys-Microstructure and Tensile Properties of Hot Worked High Nb Containing TiAl Alloy on Industrial Scale

Microstructure Evolution of Ti–46Al–6Nb–（Si,B） Alloys During Heat Treatment with W Addition

First-principles study for quasi-static growth model in FeAl intermetallic based on Wulff cluster model

In Situ Small Angle X-Ray Scattering Investigation of Ultrasound Induced Nucleation in A Metallic Alloy Melt

Atomic tuning effect of TiB2 particles on the liquid phase separation behavior of an Al-Bi immiscible alloy