Abstract:In recent years, hafnium oxide (HfO2) has gained increasing interest because of its high dielectric constant, excellent thermal stability, and high band gap. Although HfO2 bulk and film materials have been prepared and well-studied, HfO2 fibers, especially hollow fibers, have been less investigated. In this study, we present a facile preparation method for HfO2 hollow fibers through a unique integration of the sol-gel process and electrospinning technique. Initially, polystyrene (PS) fibers are fabricated by using electrospinning, followed by dipping in a HfO2 precursor solution, resulting in HfO2-coated PS fibers. Subsequent thermal treatment at 800 °C ensures the selective pyrolysis of the PS fibers and complete condensation of the HfO2 precursors, forming HfO2 hollow fibers. Scanning electron microscopy (SEM) characterizations reveal HfO2 hollow fibers with rough surfaces and diminished diameters, a transformation attributed to the removal of the PS fibers and the condensation of the HfO2 precursors. Our study also delves into the influence of precursor solution molar ratios, showcasing the ability to achieve smaller HfO2 fiber diameters with reduced precursor quantities. Validation of the material composition is achieved through thermogravimetric analysis (TGA) and energy-dispersive spectroscopy (EDS) mapping. Additionally, X-ray diffraction (XRD) analysis provides insights into the crystallinity of the HfO2 hollow fibers, highlighting a higher crystallinity in fibers annealed at 800 °C compared with those treated at 400 °C. Notably, the HfO2 hollow fibers demonstrate a water contact angle (WCA) of 38.70 ± 5.24°, underscoring the transformation from hydrophobic to hydrophilic properties after the removal of the PS fibers. Looking forward, this work paves the way for extensive research on the surface properties and potential applications of HfO2 hollow fibers in areas such as filtration, energy storage, and memory devices.

Effect of calcination temperatures on HfO2 fibers via electrospinning

Effect of hafnium oxide on continuous aluminum oxide-mullite-hafnium oxide composite ceramic fibers

Studies on the Crystallization Behavior of Al2O3-HfO2 Ceramic Fibers Prepared by Melt-spinning of Polymer Precursors

Effect of Heating Rate on Morphology and Structure of Cofe2o4 Nanofibers

Continuous aluminum oxide-mullite-hafnium oxide composite ceramic fibers with high strength and thermal stability by melt-spinning from polymer precursor

Zirconia-alumina multiphase ceramic fibers with exceptional thermal stability by melt-spinning from solid ceramic precursor

Ultra-high Melting Point Ho3+, Yb3+ Co-Doped HfO2 Single-Crystal Fibers for High-Precision and Robust Ratiometric Thermometry Towards Harsh Environments

Synthesis of Ultra‐fine Rare‐earth‐zirconate High‐entropy Ceramic Fibers Via Electrospinning

Effect of sintering additives on the sintering and ablation resistance of novel HfO 2 -ThO 2 high-temperature multiphase oxides

Effect of Heat Treatment on Properties of HfO2 Film Deposited by Ion-Beam Sputtering

Preparation of ultrafine flexible alumina fiber for heat insulation by the electrospinning method

Ultra-high temperature resistance of one-dimensional hafnium carbide wrapped with pyrolytic carbon up to 2450 °C

Hollow Hafnium Oxide (HfO2) Fibers: Using an Effective Combination of Sol-Gel, Electrospinning, and Thermal Degradation Pathway

Fine‐Grain High‐Performance Densified Oxide Fibers Produced by Open Ultrafast High‐Temperature Sintering

Preparation of silicon-nitride ceramic fibers with hafnium compounds loaded on the surface and the high temperature properties

Effect of TiO2 doping on the fracture toughness and thermal conductivity of HfO2 ceramic

Low-temperature Rapid Synthesis of Ultrafine Hafnium Carbide Ceramic Powders

Effect of Calcination Temperature on Microstructure and Magnetic Properties of Ni0.3cu0.2zn0.5fe2o4 Nanofibers

Effect of heat‐treatment on the microstructure and room‐temperature mechanical properties of alumina–silica fiber

Efficient Fabrication of Light Cf/SiHfBOC Composites with Excellent Thermal Shock Resistance and Ultra-High-temperature Ablation Up to 1800 °C

Preparation of Continuous Aluminum Oxide Fibers with Silicon Oxide and Zirconium Oxide Additives