Abstract:Currently, it is state of the art to use precipitation hardening 6000-series aluminum alloys to manufacture high-strength aluminum automotive parts by extrusion or in a cold forming process. Alternatively, it is also possible to produce such parts by the use of non-precipitation hardening 5000-series aluminum alloys in a work-hardened condition. Therefore, BENTELER Automobiltechnik GmbH developed a special sheet forming process, henceforth referred to as "flash forming process". The application of the flash forming process, consisting of a rapid heat treatment and a subsequent cold die stamping, increases the forming capability of the work-hardened 5000-series aluminum sheets and results in high-strength parts with a very good ductility and weldability. In addition, this thermal assisted forming process allows a cost-saving production of such high-strength aluminum parts due to lower material costs of 5000-series aluminum alloys than those of a 6000-series material. Furthermore, the weight-saving effects of "flash formed" parts can be higher compared to extruded or cold formed 6000-series aluminum alloys. The suitability of the process is evaluated by forming a commercial AW-5182 H18 aluminum sheet to a crash-relevant automotive part. However, to accurately simulate the flash forming process itself, a temperature dependent fracture model is necessary. Investigations on a coupon basis also showed that the effect of adiabatic heating due to plastic work cannot be neglected. In cooperation with Paderborn University, a detailed mechanical testing, aided by digital image correlation (DIC) and thermal imaging, is carried out to characterize the yield, hardening and fracture behavior at elevated temperatures. The experimental tests are followed by the calibration of a FLD and an incremental stress state dependent fracture model in LS-DYNA. Finally, the simulation models are validated on a cross die deep drawn cup.

Experimental and Simulation Studies of Erichsen Cupping Test on Aluminum(7075) Sheet Using Damage Theory

Ductile damage prediction of AA 5754 sheet during cold forming condition

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Characterization and prediction of fracture in 6000- and 7000-series aluminum alloy sheet under various stress states

Predicting Sheet Forming Limit of Aluminum Alloys for Cold and Warm Forming by Developing a Ductile Failure Criterion

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Damage and failure characterization of 7075 aluminum alloy hot stamping

Ductile Fracture and S–N Curve Simulation of a 7075-T6 Aluminum Alloy under Static and Constant Low-Cycle Fatigue

Fatigue Damage Behavior and Mechanism Research of 2198 Aluminum–Lithium Alloy Sheet with Error Holes

Formability enhancement of EN AW-5182 H18 aluminum alloy sheet metal parts in a flash forming process: testing, calibration and evaluation of fracture models

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Damage in Creep Aging Process of an Al-Zn-Mg-Cu Alloy: Experiments and Modeling

Forming Limit Prediction of Anisotropic Aluminum Magnesium Alloy Sheet AA5052-H32 Using Micromechanical Damage Model

Enhanced CDM model accounting of stress triaxiality and Lode angle for ductile damage prediction in metal forming

Prediction of limit strains in hot forming of aluminium alloy sheets

Fracture behavior of 7075-T6 aluminum alloy under electromagnetic forming and traditional stamping

Experimental and numerical investigation of failure during bending of AA6061 aluminum alloy sheet using the modified Mohr-Coulomb fracture criterion

Modeling of the ductile damage – Application for bar shearing

Experimental Investigation on the Formability of Al-Mg Alloy 5052 Sheet by Tensile and Cupping Test

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models