Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Nitrogen absorption behavior and mechanism of TiZrMnFe getter alloy

Phase Formation in Nitrogen Ion Implanted Ti–Al–Zr Alloy and Modification of Corrosion Property

Phase Structures and Electrochemical Properties of V2.1TiNi0.4Zrx (x=0−0.06) Hydrogen Storage Electrode Alloys

Effect of Adding Al on the Phase Structure and Gettering Performance of TiZrV Non-Evaporable Getter Materials

Microstructure and Electrochemical Properties of V_(2.1)TiNi_(0.4)Zr_(0.06)Cu_(0.03)M_(0.10)(M=Cr, Co, Fe, Nb, Ta) Hydrogen Storage Alloys

Phase formation and modification of corrosion property of nitrogen implanted Ti–Al–V alloy

A Study of Effect of Nitrogen Implantation on Corrosion Properties of Ti-Al-Zr Alloy

Phase composition for Zr(Mn1-xNix)2 alloys

Surface Characteristics and Oxidation Behavior of Nitrogen Ion-Implanted Zr–Sn–Nb Alloy

Surface Characterization of a Ti–2Al–2.5Zr Alloy by Nitrogen Ion Implantation

Nitriding Behavior of Nanocrystalline NdFe10.5VTi0.5 Compounds

Influence of Nitrogen on the Microstructure and Solidification Behavior of High Nb Containing TiAl Alloys

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

First-Principles Study of Nitrogen Adsorption and Dissociation on ZrMnFe(110) Surface

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

Microstructure evolution and mechanism during nitridation of carbon-containing internal gelation-derived zirconia

Surface Modification of a Ti-2Al-2.5Zr Alloy by N Ion Implantation

Microstructure and Mechanical Properties of As-Cast Ti-N Alloy

High Temperature Gas Nitridation and Wear Resistance of TiAl Based Alloys

Effect of Nitridation on the Oxidation Behavior of TiAl-based Intermetallic Alloys

Efficient and cost-effective method to synthesize highly purified Ti4AlN3 and Ti2AlN