Abstract:Cr2AlB2 and Cr4AlB4 are members of the MAB phases that exhibit unique properties of both metals and ceramics. However, despite these unique characteristics, Cr2AlB2 and Cr4AlB4 phase coatings have not been widely investigated. In this study, Cr2AlB2 and Cr4AlB4 MAB phase coatings were fabricated by magnetron sputtering at room temperature and post-annealing. A composite target, consisting of a phase-pure disc-shaped CrB target overlapped by uniformly dispersed fan-shaped Al slices, was placed parallel to the substrates. The Al content of the coatings was adjusted by altering the areal proportion of the Al slices. MAB phases have crystallized upon post-annealing the as-deposited coatings on Al2O3(0001) substrates in Ar. The phase compositions and morphologies of the crystalline coatings were found to be dependent on the Al content and the annealing temperature. As-deposited coatings with a Cr:Al:B ratio close to 2:1:2 could crystallize as pure and dense Cr2AlB2 phases within the temperature range of 650–800 °C; higher annealing temperatures resulted in the decomposition of Cr2AlB2, while crystallization at lower temperatures was not evident from X-ray diffraction. As-deposited coatings with a Cr:Al:B ratio close to 3:1:3, despite containing a relatively higher Al content than required by the stoichiometry of Cr4AlB4, exhibited insufficient crystallization of Cr4AlB4 with unknown phases below 840 °C. Higher annealing temperatures resulted in the coexistence of Cr4AlB4 and CrB, indicating that achieving phase-pure and well-crystallized Cr4AlB4 coatings proved challenging, possibly due to the inevitable loss of Al during annealing. The configuration of the composite target and the substrates provides a promising strategy for fabricating phase-pure and dense Cr2AlB2 coatings.

MAB phase-alumina composite formation via aluminothermic exchange reactions

Fabrication of Cr2AlB2 and Cr4AlB4 MAB Phase Coatings by Magnetron Sputtering and Post-Annealing

Phase stability and mechanical property trends for MAB phases by high-throughput ab initio calculations

Making high-performance MoAlB ceramics by hot pressing combustion-synthesized powders

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Aluminum Hydroxide Secondary Building Units in a Metal–Organic Framework Support Earth-Abundant Metal Catalysts for Broad-Scope Organic Transformations

Phase Formation during the Synthesis of the MAB Phase from Mo-Al-B Mixtures in the Thermal Explosion Mode

Synthesis, microstructure and properties of MoAlB MAB phase films

Ultra-fast synthesis and thermodynamic analysis of MoAlB by self-propagating high temperature combustion synthesis

Self-propagating high-temperature synthesis of MoAlB boride ceramics based on MAB-phase

Structural, elastic, mechanical, electronic, damage tolerance, fracture toughness, and optical properties of Cr–Al–B MAB phases studied by first-principles calculations

Defect behavior and radiation tolerance of MAB phases (MoAlB and Fe2AlB2) with comparison to MAX phases

Effects of Zn and Si on the microstructure evolution of the Cr-Al-B MAB phase contained in the periodic layered structure formed in-situ

First-principles Calculations on Ti2AlB2, Ti3AlB4 and Ti4AlB6, Three Potential New Members of the Orthorhombic MAB Phase

Enhancing Oxidation Resistance of MoAlB based on its Anisotropic Oxidation Mechanism: A Theoretical Calculation Guided Experimental Investigation

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Novel MAB phases and insights into their exfoliation into 2D MBenes

The structure and phase transformations in fumed transition alumina by X-ray diffraction and solid-state NMR

Microstructure and Mechanical Properties of MoAlB Particles Reinforced Al Matrix Composites by Interface Modification with in Situ Formed Al12Mo

Exploring the Relationship between the Structural Characteristics and Mechanical Behavior of Multicomponent Fe-Containing Phases: Experimental Studies and First-Principles Calculations