Abstract:Patients with stroke and other neurological disorders like trauma, multiple sclerosis (MS) experience different lower limb disabilities due to various damages in neuromuscular system. Orthotic devices are prescribed to compensate muscle weakness, prevent unwanted movement of the impaired limb. Design and manufacturing methods of lower limb orthoses involve manual techniques e.g. casting and moulding of the limbs to be treated, vacuum forming etc. Such methods are time consuming, require skilful labour and often based on trial and error rather than systematic engineering and evidence based principles. In recent years, 3D scanning and reconstruction of medical images facilitate making 3D computer models of lower limb, which allows computer aided design (CAD) tools to be incorporated in orthotic design. All these approaches rely on the external model of lower limb and limited to single piece plastic ankle foot orthosis (AFO) only. To design orthosis with articulated joint, precise alignment of anatomical joint and mechanical axis is necessary. However, it is difficult to infer joint axes from external models as it is partially specified by skeletal structure. In our research, a design approach for custom knee ankle foot orthosis and ankle foot orthosis with commercially available joints has been demonstrated, which involves skeletal structure of lower limb for locating anatomical axes to ensure accurate alignment of orthotic mechanical joint. CAD models of the orthotic components were developed based on the 3D models of a healthy subject’s lower limb, which were developed through 3D reconstruction. Components of the orthotics were fabricated by rapid prototyping and machining to demonstrate the new approach. The fabricated orthoses were evaluated by a certified orthotist and the performance of the custom made AFO was compared statistically with a pre-fabricated AFO with similar ankle joint. The manufacturing process requires approximately 50% lesser time to develop AFO and 70% lesser time to develop KAFO compared to Brace and Limb laboratory of University Malaya. Unlike traditional approaches, the design technique facilitates exact positioning of articulated joint. The developed orthoses are light in weight, comfortable and easy to don and doff. Biomechanical test implies that the fabricated AFO provides better range of motion than a pre-fabricated AFO with same ankle joint. Although the custom AFO allowed significantly higher plantar flexion during pre-swing compared to pre-fabricated AFO condition (MD = 1.734, MSD = 1.55), the subject’s ankle required to generate significantly higher power with the pre-fabricated AFO (MD = 0.141, MSD = 0.035). These findings suggest that the subject had to overcome higher resistance with pre-fabricated AFO compared to custom made AFO. Simultaneous viewing of exterior and skeletal geometry might help the clinicians modify the design to enhance performance of the orthotic device.

Structural testing of a passive polycentric knee joint with advanced functionalities designed and developed for patient-specific fitting

Design and analysis of polycentric prosthetic knee with enhanced kinematics and stability

Computational assessment of carbon fabric reinforced polymer made prosthetic knee: Mechanics, finite element simulations and experimental evaluation

Numerical simulation and experimental testing for static failure prediction in additively manufactured below-knee prosthetic sockets

Design, Control, and Validation of a Polycentric Hybrid Knee Prosthesis

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Development of a test rig for the diagnosis of arthritic knee joint defects in the case of lower extremity amputees in orthopaedic technology

A preclinical numerical assessment of a polyetheretherketone femoral component in total knee arthroplasty during gait

Development of an Integrated Powered Hip and Microprocessor-Controlled Knee for a Hip-Knee-Ankle-Foot Prosthesis

Design, Manufacture, and Experimental Validation of a Hydraulic Semi-Active Knee Prosthesis

Design, Kinematics and Gait Analysis, of Prosthetic Knee Joints: A Systematic Review

Design and evaluation of a wedge-shaped adaptive knee orthosis for the human lower limbs

Impact of Structural Compliance of a Six Degree of Freedom Joint Simulator on Virtual Ligament Force Calculation in Total Knee Endoprosthesis Testing

Computer integrated design and manufacturing of patient specific lower limb orthoses through 3D reconstruction / Morshed Alam

Advancing Lower Limb Prosthetics: Custom Design, Simulation, and Experimental Evaluation

Design and Validation of a Polycentric Hybrid Knee Prosthesis With Electromagnet-Controlled Mode Transition

[Structural Design and Analysis of Portable Intelligent Wheelchair for Knee Rehabilitation]

Computational biomechanical study on hybrid implant materials for the femoral component of total knee replacements

Biofusion design and parameter optimization for a novel passive assisted knee exoskeleton robot based on eight-bar mechanism

Design and Evaluation of a Novel Microprocessor-Controlled Prosthetic Knee

Fatigue Analysis of Hip Prosthesis