Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Computational assessment of carbon fabric reinforced polymer made prosthetic knee: Mechanics, finite element simulations and experimental evaluation

Design and analysis of polycentric prosthetic knee with enhanced kinematics and stability

Structural testing of a passive polycentric knee joint with advanced functionalities designed and developed for patient-specific fitting

Effect of Carbon-Fiber-reinforced Polyetheretherketone on Stress Distribution in a Redesigned Tumor-Type Knee Prosthesis: a Finite Element Analysis

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Numerical simulation and experimental testing for static failure prediction in additively manufactured below-knee prosthetic sockets

Effects of the material properties of a focal knee articular prosthetic on the human knee joint using computational simulation

Modeling and analysis of a prosthetic foot: A numerical simulation case study

Advancing Lower Limb Prosthetics: Custom Design, Simulation, and Experimental Evaluation

The numerical simulation of a new biomimetic silicone layer component of total knee prosthesis

Study and numerical analysis of Von Mises stress of a new tumor-type distal femoral prosthesis comprising a peek composite reinforced with carbon fibers: finite element analysis

Analysis and Evaluation of Optimized Lower Limb Prosthetic Device

Mechanical Performance of Proximal Human Femur after Poly-Ether-ether-ketone Femoral Prosthesis Implantation

A preclinical numerical assessment of a polyetheretherketone femoral component in total knee arthroplasty during gait

Biomechanical Evaluation of Composite Femoral Prosthesis

Computer-aided design of individualized artificial knee prosthesis

Predicting Mechanical Properties of Polymer Materials Using Rate-Dependent Material Models: Finite Element Analysis of Bespoke Upper Limb Orthoses

Finite Element Analysis of A Retrieved Custom-Made Knee Prosthesis

Structural stability of a polyetheretherketone femoral component-A 3D finite element simulation

A SENSORIZED 3D-PRINTED KNEE TEST RIG FOR EXPERIMENTAL VALIDATION OF PATELLAR TRACKING AND CONTACT SIMULATION AFTER TOTAL KNEE REPLACEMENT

Prediction of in vivo joint mechanics of an artificial knee implant using rigid multi-body dynamics with elastic contacts.