Abstract:Objective This study investigated the stress distribution in a femur after a cemented prosthetic replacement surgery in elderly patients with a partial marrow type I intertrochanteric fracture and compared the differences in stress distribution between a long- and short-stem prosthetic replacement. Methods A spiral computed tomography (CT) scan was used on the volunteer’s right femur to obtain image data, which were processed with the Mimics software and the modeling software to reconstruct a three-dimensional model of the femur. On this basis, the three-dimensional physical models for a partial marrow type intertrochanteric fracture, long- and short-stem femoral prostheses, and the mantle layer of cement were established. Finally, the three-dimensional finite element models of the long- and short-stem femoral prostheses as a treatment of an intertrochanteric fracture were established using the software for finite element analysis, and the biomechanical analysis was implemented for the models. Results The stress distribution in the femur after the cemented long- or short-stem prosthetic replacement did not change significantly; it still gradually increased from the proximal end to the distal end, reaching the peak value at the lower 1/3 of the medial and lateral junction, and then decreased to the end. Although a stress concentration zone formed in the medial and lateral end of the bone cement-prosthetic stem interface in the short-stem prosthesis, which had a lateral peak value of 15.3 MPa, it did not exceed the fatigue strength of the bone cement. Alternatively, a stress concentration zone formed in the distal medial and lateral end of the bone cement-prosthetic stem interface and the medial middle part of the shaft in the long-stem prosthesis, which showed a peak value that was also lower than the fatigue strength of the bone cement. No significant stress concentration zones were found in the femoral calcar reconstructed by bone cement. Conclusion The stress distribution in the femur did not change significantly after cemented long- and short-stem prosthetic replacements were used for elderly patients with a partial marrow type I intertrochanteric fracture. The probability of loosening of the cemented long-stem prosthesis was comparable to that of the short-stem prosthesis, but the latter may be more suitable for treating elderly patients with a partial marrow type I intertrochanteric fracture due to the shorter surgery time, minor trauma, and fewer complications.

Study and numerical analysis of Von Mises stress of a new tumor-type distal femoral prosthesis comprising a peek composite reinforced with carbon fibers: finite element analysis

Effect of Carbon-Fiber-reinforced Polyetheretherketone on Stress Distribution in a Redesigned Tumor-Type Knee Prosthesis: a Finite Element Analysis

Tuberosity reconstruction baseplate for shoulder hemiarthroplasty: Morphological design and biomaterial application

Carbon fiber reinforced PEEK Optima--a composite material biomechanical properties and wear/debris characteristics of CF-PEEK composites for orthopedic trauma implants

Finite Element Analysis of Femoral Stress Changes after Total Hip Arthroplasty

Finite element investigation into the use of carbon fibre reinforced PEEK laminated composites for distal radius fracture fixation implants

Carbon fiber-reinforced PEEK spinal implants for primary and metastatic spine tumors: a systematic review on implant complications and radiotherapy benefits

A preclinical numerical assessment of a polyetheretherketone femoral component in total knee arthroplasty during gait

Performance parametric formulation of carbon fiber-reinforced composite locking bone implant plates based on finite-element analysis

Finite element stress analysis of the bearing component and bone resected surfaces for total ankle replacement with different implant material combinations

Stress Analysis and Shape Design of a Femoral Hip Prosthesis

Theoretical analysis of changes in femoral stresses after total hip arthroplasty]

Computational assessment of carbon fabric reinforced polymer made prosthetic knee: Mechanics, finite element simulations and experimental evaluation

Stress Shielding and Bone Resorption of Press-Fit Polyether–Ether–Ketone (PEEK) Hip Prosthesis: A Sawbone Model Study

Exploring Advanced Functionalities of Carbon Fiber-Graded PEEK Composites as Bone Fixation Plates Using Finite Element Analysis

Reconstruction of Severe Acetabular Bone Defect with 3D Printed Ti6Al4V Augment: A Finite Element Study

The Comparative Analysis with Finite Element for Cemented Long- and Short-Stem Prosthetic Replacement in Elderly Patients with a Partial Marrow Type I Intertrochanteric Fracture

Assessing the influence of gastrocnemius reconstruction on stress distribution of femoral tumor rotating hinge knee prosthesis via finite element analysis

A Three – Dimensional Finite Element Analysis of Polyetheretherketone PEEK in Dental Implant Prosthesis: A Novel Implant System

The Use of Carbon-Fiber-Reinforced (CFR) PEEK Material in Orthopedic Implants: A Systematic Review

The primary stability of a cementless PEEK femoral component is sensitive to BMI: A population-based FE study