Abstract:The PSf casting solution required degassing, sealing, and humidity and temperature control.PA layer formation on the top surface of the PSf substrate resulted in the highest FO performance.GO modification of the PA layer considerably enhanced water flux and reduced reverse solute fluxThe FO membranes exhibited high rejection efficiency for dyes used in the textile industry.The application of FO for water recovery is economic and environmentally friendly.In this study, the preparation procedures for the polysulfone (PSf) substrate and polyamide (PA) selective layers were systematically investigated to determine their effects on the separation performance of thin-film composite (TFC) forward osmosis (FO) membranes in terms of the permeate flux (Jw) and reverse solute flux (Js). Furthermore, the PA active layer was modified by adding different proportions of an emerging material, graphene oxide (GO), to increase Jw and decrease Js. The experimental results indicated that special attention should be paid to the preparation of the PSf casting solution, which required thorough degassing, sealing, and humidity and temperature control. The optimum casting height was discovered to be 175 μm. For PA layer formation, the same amount of polymer solutions (resulting thickness of 78.5 μm) on the top surface of the PSf substrate (on the side facing the water during phase inversion) resulted in the highest FO performance. GO modification of the PA layer at the dosage of 0.0175 wt% considerably enhanced Jw to 14 L m−2 h−1 and reduced Js to 0.23 mol m−2 h−1. However, higher GO dosage (0.02 wt%) led to lower membrane performance due to aggregation of GO nanoparticles, as confirmed using scanning electron microscopy. Next, the prepared membranes were applied to dye rejection and sludge concentration for water recovery. The virgin and modified FO membranes both exhibited high rejection efficiency (≥ 96.0%) for dyes commonly used in the textile industry. The 0.0175%-GO-modified FO membrane exhibited a higher concentration factor (1.67) and greater water recovery (40.0%) than the virgin membrane (1.45 and 31.2%, respectively). Therefore, the application of FO for water recovery is economic and environmentally friendly in terms of saving the transportation cost of sludge disposal while recovering water for reuse in wastewater treatment plants.

Electrospun nanofiber based forward osmosis membrane using graphene oxide as substrate modifier for enhanced water flux and rejection performance

Graphene Oxide Based Membrane Intercalated by Nanoparticles for High Performance Nanofiltration Application

Development of high-performance electrospun nanofiber based forward osmosis membrane by introducing graphene oxide‐calcium carbonate particle composite intermediate layer

Impact of Graphene Oxide on Properties and Structure of Thin-Film Composite Forward Osmosis Membranes

Fabrication and modification of forward osmosis membranes by using graphene oxide for dye rejection and sludge concentration

Decreased Cross-Linking in Interfacial Polymerization and Heteromorphic Support Between Nanoparticles: Towards High-Water and Low-Solute Flux of Hybrid Forward Osmosis Membrane.

Graphene oxide incorporated thin-film composite membranes for forward osmosis applications

Graphene Oxide Modified Graphitic Carbon Nitride As A Modifier for Thin Film Composite Forward Osmosis Membrane

A Freestanding Graphene Oxide Framework Membrane for Forward Osmosis: Separation Performance and Transport Mechanistic Insights

Electrospun nanofiber supports with bio-inspired modification enabled high-performance forward osmosis composite membranes

Construction of facilitated mass transfer composite membrane with triple-layer water nanochannel architecture for forward osmosis process using cGO-coated polysulfone separation membrane as the substrate

Polydopamine nanoparticles modified nanofiber supported thin film composite membrane with enhanced adhesion strength for forward osmosis

Preparation and characterization of high-performance electrospun forward osmosis membrane by introducing a carbon nanotube interlayer

Polyamide Membrane with an Ultrathin GO Interlayer on Macroporous Substrate for Minimizing Internal Concentration Polarization in Forward Osmosis

Comparison of Performance and Biofouling Resistance of Thin-Film Composite Forward Osmosis Membranes with Substrate/active Layer Modified by Graphene Oxide.

High Water Permeable Free-Standing Cellulose Triacetate/Graphene Oxide Membrane with Enhanced Antibiofouling and Mechanical Properties for Forward Osmosis

Chemically Cross-Linked Graphene Oxide as a Selective Layer on Electrospun Polyvinyl Alcohol Nanofiber Membrane for Nanofiltration Application

Fabrication of high performance TFN membrane incorporated with graphene oxide via support-free interfacial polymerization

High performance forward osmosis membrane with ultrathin hydrophobic nanofibrous interlayer

Graphene Oxide Incorporated Forward Osmosis Membranes with Enhanced Desalination Performance and Chlorine Resistance

Porous graphene oxide surface-coated thin-film composite membrane for simultaneously increasing permeation performance and organic-fouling migration capacities