Abstract:Background: Fe80B20 amorphous alloys exhibit excellent soft magnetic properties, high abrasive resistance and outstanding corrosion resistance. In this work, Fe80B20 amorphous micro-fibers with HC of 3.33 Oe were firstly fabricated and the effects of annealing temperature on the structure and magnetic properties of the fibers were investigated. Methods: In this study, Fe80B20 amorphous fibers were prepared by the single roller melt-spinning method. The structures of as-spun and annealed fibers were investigated by X-ray diffractometer (XRD) (PANalytical X,Pert Power) using Cu Kα radiation. The morphology of the fibers was observed by scanning electron microscopy (SEM) (HITACHI-S4800). Differential scanning calorimetry (DSC) measurements of the fibers were performed on Mettler Toledo TGA/DSC1 device under N2 protection. Vibrating sample magnetometer (VSM, Versalab) was used to examine the magnetic properties of the fibers. The resonance behavior of the fibers was characterized by an impedance analyzer (Agilent 4294A) with a home-made copper coil. Results: The X-ray diffusion (XRD) patterns show that the fibers remain amorphous structure until the annealing temperature reaches 500°C. The differential scanning calorimetry (DSC) results show that the crystallization temperature of the fibers is 449°C. The crystallization activation energy is calculated to be 221 kJ/mol using Kissinger formula. The scanning electron microscopy (SEM) images show that a few dendrites appear at the fiber surface after annealing. The result indicates that the coercivity HC (//) and HC (⊥) slightly increases with increasing annealing temperature until 400°C, and then dramatically increases with further increasing annealing temperature which is due to significant increase in magneto-crystalline anisotropy and magneto-elastic anisotropy. The Q value firstly increases slightly when the annealing temperature rises from room temperature (RT) to 300°C, then decreases until 400°C. Eventually, the value of Q increases to ~2000 at annealing temperature of 500°C. Conclusions: In this study, Fe80B20 amorphous fibers with the diameter of 60 μm were prepared by the single roller melt-spinning method and annealed at 200°C, 300°C, 400°C, and 500°C, respectively. XRD results indicate that the fiber structure remains amorphous when the annealing temperature is below 400°C. α-Fe phase and Fe3B phase appear when the annealing temperature rises to 500°C, which is above the crystallization temperature of 449°C. The recrystallization activation energy is calculated to be 221 kJ/mol. The coercivity increases with increasing annealing temperature, which attributes to the increase of total anisotropy. All the as-spun and annealed fibers exhibit good resonance behavior for magnetostrictive sensors.

The effect of annealing on kink band formation in Ag/Fe nanolaminates

Effect of Annealing Temperature on Permeability and Giant Magneto-Impedance of Fe-based Amorphous Ribbon

Effect of Annealing on the Microstructure and Magnetic Properties of Fe-based Nanocomposite Materials

Effect of Chemical Ordering Annealing on Martensitic Transformation and Superelasticity in Polycrystalline Ni–Mn–Ga Microwires

Unraveling kinking: a plasticity enhancing failure mode in high strength nano metallic laminates

Quasi in-situ investigation on kinking behavior of Fe-Cr-Al alloy during thermal compression

Formation Mechanism of Stress-Induced Anisotropy in Stress-Annealed Fe-based Nanocrystalline Ribbon Alloys

Effect of Annealing Treatment on Mechanical Properties of Nanocrystalline α-iron: an Atomistic Study

New kink-band formation mechanism discovered in Zn-Al alloy with mille-feuille microstructure

Interface-dominated plasticity and kink bands in metallic nanolaminates

Annealing Effects and Short-Range Ordering in the Non-Magnetostrictive Amorphous Alloy Co 58 Ni 10 Fe 5 Si 11 B 16

Effect of pre-annealing on microstructures and soft magnetic properties of nanocrystalline Fe_(86)Zr_7B_6Cu_1 alloy

Micro-Mechanical Analysis about Kink Band in Carbon Fiber/Epoxy Composites under Longitudinal Compression

Annealing Effect On The Microstructure Modification And Tribological Properties Of Amorphous Carbon Nitride Films

Orientation dependence of the nanocrystallization and magnetic behavior during annealing of the FINEMET alloy

Real-Time Observation of Nanoscale Kink Band Mediated Plasticity in Ion-Irradiated Graphite: An In Situ TEM Study

Crystallographic Anisotropy Dependence of Interfacial Sliding Phenomenon in a Cu(16)/Nb(16) ARB (Accumulated Rolling Bonding) Nanolaminate

Annealing Effects on the Structural and Magnetic Properties of Off-Stoichiometric Fe-Mn-Ga Ferromagnetic Shape Memory Alloys

Lamellar kinking in primary hot working of titanium alloy: Cross-scale behavior and mechanism

Deformation mechanism in nanolaminate FeCrAl alloys by in situ micromechanical strain rate jump tests at elevated temperatures

Effects of annealing on the structure and magnetic properties of Fe80B20 magnetostrictive fibers