Abstract:The large diameter metal shell component (LDMSC) is an important part of gas insulated (metal-enclosed) switchgear (GIS). The LDMSC with multi branches is filled with gas under certain pressure. The plastic forming process is an efficient approach to manufacturing the high reliability LDMSC. The warm flanging process has been widely used to form LDMSC using aluminum alloy. The forming process is characterized by local heating, and the distribution of temperature is strongly inhomogeneous. Although the wall thickness of the shell is 10 mm to 20 mm, the ratio of outer diameter to thickness is more than 40. These present some difficulties in the flanging process and result in some forming defects. Detailed forming characteristics are hard to obtain by analytical and experimental methods. Thus, the through-process finite element (FE) modeling considering heating, forming, unloading, and cooling is one of the key problems to research the manufacturing process of LDMSC. In this study, the through-process FE modeling of the warm flanging process of LDMSC using aluminum alloy was carried out based on the FORGE. The thermo-mechanical coupled finite element method was adopted in the modeling, and the deformation of the workpiece and the die stress were considered together in the modeling. A full three-dimensional (3D) geometry was modeled due to inhomogeneous distribution in all directions for the temperature field. The simulation data of local flame heating could be transferred seamlessly to the simulations of the deforming process, the unloading process, and the cooling process in the through-process FE model. The model was validated by comparison with geometric shapes and forming defects obtained from the experiment. The developed FE model could describe the inhomogeneous temperature field along circumferential, radial, and axial directions for the formed branch as well as the deformation characteristic and the unloading behavior during the warm flanging process. By using the FE model, the forming defects during the flanging process and their controlling characteristics were explored, the evolution of the temperature field through the whole process was studied, and deformation and springback characteristics were analyzed. The results of this study provide a basis for investigating deformation mechanisms, optimizing processes, and determining parameters in the warm flanging process of a large-diameter aluminum alloy shell component.

Analysis of Hot Continuous Process of Special Gas Storage Vessel for Semiconductor Cleaning Process

Mechanical Analysis of Carbon Fiber Filament Wound Hydrogen Storage Vessel with Aluminum Alloy Liner

Mechanical Analysis of Carbon Fiber Wound High Pressure Hydrogen Storage Vessel and Prestress Control in Manufacturing Process

Mechanical Analysis and Optimal Design for Carbon Fiber Resin Composite Wound Hydrogen Storage Vessel With Aluminum Alloy Liner

A Heat-Balance Method for Autoclave Process of Composite Manufacturing

Optimal design of curing process for manufacturing a high pressure hydrogen vessel (type 4)

A Simple Method of Reducing Coolant Leakage for Direct Metal Printed Injection Mold with Conformal Cooling Channels Using General Process Parameters and Heat Treatment

Research on the integral forming process of thin walled and thick mouth seamless gas cylinders

Data-Driven Analysis of High-Temperature Fluorocarbon Plasma for Semiconductor Processing

Study on Whole Forming Process of Unequal Thickness Inner Liner for High-Pressure Gas Cylinder

Design and numerical analysis of a novel argon gas tube to reduce impurities in large size casting crystalline silicon furnace

Numerical analysis of process induced stress field for composite filament wound vessel with metal liner

Through-Process Finite Element Modeling for Warm Flanging Process of Large-Diameter Aluminum Alloy Shell of Gas Insulated (Metal-Enclosed) Switchgear.

Application of additive technologies for manufacturing turbine stator parts in aircraft engines

DEVELOPMENT OF LIGHTWEIGHT DESIGN AND MANUFACTURE OF HEAVYDUTY PRESSURE VESSELS IN CHINA

Design and Preparation of Lightweight Composite Pressure Vessels with Ultra Thin Metal Liner

Analysis of the main factors affecting mass production in the plastic molding process by using the finite element method

NUMERICAL SIMULATION OF CURING PROCESS FOR FILAMENT WOUND PRESSURE VESSEL WITH METAL LINER

A low-cost and highly efficient method of reducing coolant leakage for direct metal printed injection mold with cooling channels using optimum heat treatment process procedures

Analysis and Optimization of the Silicone Molding Process Based on Numerical Simulations and Experiments

Design of Type-IV Composite Pressure Vessel Based on Comparative Analysis of Numerical Methods for Modeling Type-III Vessels