Abstract:This paper presents an experimental and theoretical study of surface generation in the ultra-precision grinding of hard and brittle materials. The study takes into account the material properties, the relative vibration between the grinding wheel and the workpiece, the machining parameters and the phase shift of the grinding process. The Taguchi approach is employed to study the influence of machining parameters on the surface quality and shows that the feed speed and rotational speed of the workpiece are key factors. Experiments have been conducted to study individual variables, and the results further show that the feed rate and the cross-feed distance have a significant effect on surface generation. It is found that the spirals around the central area of the workpiece are the primary mechanism for surface generation, which originates from the synchronous relative tool-work vibration. The integral part of the ratio of the rotational speed of the grinding wheel to rotational speed of the workpiece determines the number of spirals and its fractional part controls the spiral geometry. A theoretical model for predicting the single spiral generation has been developed to explain the accumulation of the phase shift and the geometry. The changeable feed speed near the end of grinding is also modelled, revealing the approximate straight lines around one circle in the central region. The simulated results indicate that the theoretical models and the ground surfaces are in close agreement. The scallop-height model is developed to calculate the influence of phase shift on surface quality, and it is found that the phase shift near the medium value can effectively improve surface quality. Finally, a comparison of different surface generation mechanisms in grinding mould steel, tungsten carbide (WC) and reaction bonded silicon carbide (RB-SiC) is made. It is interesting to note that the Spanzipfel effect contributes to the surface generation not only on ductile materials such as mould steel but also on brittle materials such as WC and RB-SiC. The Spanzipfel effect is the most significant in grinding mould steel. For WC and RB-SiC, the ground surface contains both a ductile region and a brittle region in the form of micro-fractures.

Cutting depth-oriented surface morphology control in diamond-turning brittle single-crystal germanium

Controllable Diamond Cutting of Structured Surfaces with Subnanometric Height Features on Silicon

Generation mechanism and dual-dynamics simulation of surface patterns in single-point diamond turning of single-crystal copper

Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning

Effects of processing parameters and grinding direction on the material removal mechanism of (100) surface single crystal diamond in self-rotating mechanical grinding

Anisotropic cutting mechanisms on the surface quality in ultra-precision machining of R-plane sapphire

Study On The Control Of Surface Roughness In Single Point Diamond Turning

Sculpturing of single crystal silicon microstructures by elliptical vibration cutting

Atomistic origin of brittle-to-ductile transition behavior of polycrystalline 3C–SiC in diamond cutting

Influence of diamond abrasives on material removal of single crystal SiC in mechanical dicing

An analytical force and energy model for ductile-brittle transition in ultra-precision grinding of brittle materials

Atomistic investigation of machinability of monocrystalline 3C–SiC in elliptical vibration-assisted diamond cutting

An experimental and theoretical analysis of surface generation in the ultra-precision grinding of hard and brittle materials

Molecular Dynamics Analysis Micro-Mechanism Of Ductile Machining Single Crystal Silicon By Means Of Nanometric Cutting Technology

Study on the surface formation mechanism and theoretical model of brittle surface roughness in turning machinable ceramics

Review of ductile machining and ductile-brittle transition characterization mechanisms in precision/ultraprecision turning, milling and grinding of brittle materials

The interaction between grain boundary and tool geometry in nanocutting of a bi-crystal copper

The effect of cut depth and distribution for abrasives on wafer surface morphology in diamond wire sawing of PV polycrystalline silicon

Effect of Cutting Edge Radius on Surface Roughness in Diamond Tool Turning of Transparent MgAl2O4 Spinel Ceramic

Effect of anisotropy on deformation and crack formation under the brittle removal of 6H-SiC during SPDT process

Influence of crystallographic effect on tool wear, cutting stress, cutting temperature, cutting force and subsurface damage in nano cutting of single crystal silicon carbide