Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) have been widely studied due to their excellent photoelectric conversion performance, but the inherent chemical instability of CH(NH 2 ) 2 PbI 3 (FAPbI 3 ) has hindered its long-term development. In particular, the surface interface of the membrane has prominent humidity sensitivity due to lower activation energy, the defect of the surface interface has a strong correlation with the film stability, and the treatment result of the defect is one of the key factors to improve the long-term stability. FAPbI 3 suffers phase transition from black perovskite phase to yellow non-perovskite phase at room temperature, and the moisture will accelerate this phase transition. Interface engineering is one of the common methods to improve the stability of perovskite solar cells. In addition to interface engineering, there is also a strategy of stacking a two-dimensional (2D) perovskite layer on the surface for interface passivation. However, the preparation methods of 2D perovskite layer are most limited. In this paper, through the preparation process of the whole solution method and post-treatment mode of annealing were adopted, the hybrid perovskite solar cells of vitamin perovskite were successfully prepared. FAPbI 3 perovskite surface was uniformly spin-coated with butylamine iodide (BAI) solution, and the formation of 2D perovskite was driven on the surface of FAPbI 3 perovskite. Due to the passivation of 2D perovskite layer on the defects at the surface interface, the carrier non-radiative recombination is reduced, so that the carrier lifetime is greatly improved. Due to the hydrophobicity of long chain molecules in 2D perovskite, the long-term stability of the device has been significantly improved. Consequently, the unencapsulated device containing 2D perovskite layer remained above 80% after working nearly 1000 hours of relative humidity (RH) of 60% in ambient air at room temperature. The 2D perovskite layer can significantly improve the long-term stability of the film without affecting the charge carrier transport performance. This method to improve the stability of the device by constructing 2D perovskite layer is in line with the requirements and development trend of high-quality perovskite solar cells, and is a strategy with great development potential.

A Double Compatibilization Strategy To Boost the Performance of p - i - n Solar Cells Based on Perovskite Deposited in Humid Ambient Air

Formamidinium Perovskite Deposition in Ambient Air Environment for Inverted p-i-n Solar Cells

A Universal Strategy of Intermolecular Exchange to Stabilize α ‐FAPbI 3 and Manage Crystal Orientation for High‐Performance Humid‐Air‐Processed Perovskite Solar Cells

Boosting Long-Term Stability of Pure Formamidinium Perovskite Solar Cells by Ambient Air Additive Assisted Fabrication

Inhibition of Halide Oxidation and Deprotonation of Organic Cations with Dimethylammonium Formate for Air-Processed P–i–n Perovskite Solar Cells

Slot-die coating of a formamidinium-cesium mixed-cation perovskite for roll-to-roll fabrication of perovskite solar cells under ambient laboratory conditions

Strain Regulation Via Pseudo Halide-Based Ionic Liquid Toward Efficient and Stable -Fapbi3 Inverted Perovskite Solar Cells

Porous Lead Iodide Layer Promotes Organic Amine Salt Diffusion to Achieve High Performance p‐i‐n Flexible Perovskite Solar Cells

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Simple Method of Dual Passivation with Efficiency Beyond 20% for Fabricating Perovskite Solar Cells in the Full Ambient Air

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

Strain Regulation via Pseudo Halide‐Based Ionic Liquid toward Efficient and Stable α‐FAPbI3 Inverted Perovskite Solar Cells

On the synergistic interplay between annealing temperature and time and additive concentration for efficient and stable FAPbI 3 perovskite solar cells

Multifunctional Hybrid Interfacial Layers for High‐Performance Inverted Perovskite Solar Cells

Dual‐doping Strategy of Metal Chlorides in Ambient Air with High Humidity for Achieving Highly Air‐Stable All‐inorganic Perovskite Solar Cells

Controlling Intermediate Phase Formation to Enhance Photovoltaic Performance of Inverted FA-Based Perovskite Solar Cells

Low-cost, stable all-inorganic charge transporting layer based FAPI perovskite solar cells achieving ≈ 26% efficiency using SCAPS-1D

Managing photons and carriers by multisite chiral molecules achieving high-performance perovskite solar cells fabricated in ambient air

Preparation of 2D Perovskite Layer by Solution Method to Improve the Stability of FAPbI 3 Perovskite Solar Cells

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Improving the Performance of Inverted Formamidinium Tin Iodide Perovskite Solar Cells by Reducing the Energy-Level Mismatch