Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) have been widely studied due to their excellent photoelectric conversion performance, but the inherent chemical instability of CH(NH 2 ) 2 PbI 3 (FAPbI 3 ) has hindered its long-term development. In particular, the surface interface of the membrane has prominent humidity sensitivity due to lower activation energy, the defect of the surface interface has a strong correlation with the film stability, and the treatment result of the defect is one of the key factors to improve the long-term stability. FAPbI 3 suffers phase transition from black perovskite phase to yellow non-perovskite phase at room temperature, and the moisture will accelerate this phase transition. Interface engineering is one of the common methods to improve the stability of perovskite solar cells. In addition to interface engineering, there is also a strategy of stacking a two-dimensional (2D) perovskite layer on the surface for interface passivation. However, the preparation methods of 2D perovskite layer are most limited. In this paper, through the preparation process of the whole solution method and post-treatment mode of annealing were adopted, the hybrid perovskite solar cells of vitamin perovskite were successfully prepared. FAPbI 3 perovskite surface was uniformly spin-coated with butylamine iodide (BAI) solution, and the formation of 2D perovskite was driven on the surface of FAPbI 3 perovskite. Due to the passivation of 2D perovskite layer on the defects at the surface interface, the carrier non-radiative recombination is reduced, so that the carrier lifetime is greatly improved. Due to the hydrophobicity of long chain molecules in 2D perovskite, the long-term stability of the device has been significantly improved. Consequently, the unencapsulated device containing 2D perovskite layer remained above 80% after working nearly 1000 hours of relative humidity (RH) of 60% in ambient air at room temperature. The 2D perovskite layer can significantly improve the long-term stability of the film without affecting the charge carrier transport performance. This method to improve the stability of the device by constructing 2D perovskite layer is in line with the requirements and development trend of high-quality perovskite solar cells, and is a strategy with great development potential.

A Universal Strategy of Intermolecular Exchange to Stabilize α ‐FAPbI 3 and Manage Crystal Orientation for High‐Performance Humid‐Air‐Processed Perovskite Solar Cells

Improved Crystallinity and Self-Healing Effects in Perovskite Solar Cells Via Functional Incorporation of Polyvinylpyrrolidone

Intercepting the Chelation of Perovskites with Ambient Moisture through Active Addition Reaction for Full‐Air‐Processed Perovskite Solar Cells

Degradation mechanism and stability improvement of formamidine-based perovskite solar cells under high humidity conditions

Low-temperature synergistic effect of MA and Cl towards high-quality α-FAPbI3 films for humid-air-processed perovskite solar cells

Favorable Grain Growth of Thermally Stable Formamidinium-Methylammonium Perovskite Solar Cells by Hydrazine Chloride

Humidity‐Induced Defect‐Healing of Formamidinium‐Based Perovskite Films

Enhanced Optoelectronic Quality of Perovskite Films with Excess CH3NH3I for High-Efficiency Solar Cells in Ambient Air

Controlling Homogenous Spherulitic Crystallization for High-Efficiency Planar Perovskite Solar Cells Fabricated under Ambient High-Humidity Conditions

Crystal Growth Regulation of α‐FAPbI3 Perovskite Films for High‐Efficiency Solar Cells with Long‐Term Stability

Stabilizing precursor solution and controlling crystallization kinetics simultaneously for high‐performance perovskite solar cells

A crystal capping layer for formation of black-phase FAPbI 3 perovskite in humid air

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Stabilizing black-phase formamidinium perovskite formation at room temperature and high humidity

Moisture‐induced High‐quality Perovskite Film in Air for Efficient Solar Cells

Moisture Assisted Perovskite Film Growth for High Performance Solar Cells

Optimizing the Light-Humidity Stability of Formamidinium Halide Perovskites Through Intermediate Phase and Strain Stress Adjustment

Combined Precursor Engineering and Grain Anchoring Leading to MA‐free, Phase‐pure and Stable Α‐formamidinium Lead Iodide Perovskites for Efficient Solar Cells

Orientated crystallization of FA-based perovskite via hydrogen-bonded polymer network for efficient and stable solar cells

Preparation of 2D Perovskite Layer by Solution Method to Improve the Stability of FAPbI 3 Perovskite Solar Cells

Additive-Regulated One-Step Dynamic Spin-Coating for Fabricating High-Performance Perovskite Solar Cells under High Humidity Conditions