Abstract:Metallic components fabricated with powder bed fusion additive manufacturing (AM) processes are known to have defects arising from liquid-solid phase transformation. Friction stirring can be an effective alternative source of heat, as evidenced in some of the recently developed powder deposition-based solid-state AM processes. However, they possess practical issues such as making compacted powder feedstock beforehand, consolidation of powder filler inside the tool during deposition followed by necessary extrusion, and significant flash formation, among a few. This paper proposed a novel powder bed friction stir (PBFS) additive manufacturing process inside a specifically designed mould that could potentially mitigate such issues in the existing technologies. The process was successfully demonstrated by building single-track and parallel double-track 3D structures layer-by-layer from an AA6061 powder bed using a rotating non-consumable friction stirring tool. Furthermore, for a better understanding of the underlying process mechanics, deposits were analyzed for their surface topography, microstructural evolution, and mechanical performance under different heat inputs as well as different print locations. Different heat inputs were applied by varying the friction-stirring pitch (FS pitch) from 'Low' to 'High'. The print locations analysis was carried out in a parallel double-track fabricated at the optimal FS pitch. The results revealed that the 'High' FS pitch yielded an increased percentage of recrystallized grains and a fraction of high-angle grain boundaries as well as a larger average grain size due to the high heat input, better material intermixing, and the dominance of continuous dynamic recrystallization. As a result, an improved mechanical performance, except for the microhardness, was observed. The 'High' FS pitch also exhibited an improved surface topography. The results also revealed that the relative dominance of the re-stirring-induced recrystallization and the reheating-induced plastic deformation was the key factor for the variation of the microstructure in the longitudinal, transverse, and short-transverse directions. A gradual decrease in the tensile strength was observed from the 'Top' to the 'Bottom' segments of the overlapped region, contrary to the central region of a track.

Mechanical and Metallurgical Properties of Foam Developed by Friction Stir Tube Deposition Technique

Fabrication and characterization of aluminum foam reinforced with nanostructured γ-Al2O3 via friction stir process for enhanced mechanical performance

The Influences of Process Parameters on the Preparation of Closed-cell Aluminum foam by Friction Stir Processing

Fabrication of Uniform and Rounded Closed-Cell Aluminum Foams Using Novel Foamable Precursor Particles (FPPs)

Quasi-static Deformation Mechanism and Compressive Properties of Aluminum Foams Fabricated by Friction Stir Processing

Fabrication of foam metal in directed energy deposition applying titanium hydride

Foaming Process and Properties of 6063 Aluminum Foams by Melt Foaming Method

The influence of process parameters on the preparation of closed-cell aluminum foam by friction stir processing

Friction Stir Processing of Aerospace Aluminum Alloy by Addition of Carbon Nano Tube

Dynamic Behavior Characterization of Aluminum Alloy 7020 Manufactured Using the Additive Friction Stir Deposition Process

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

Microstructural characteristics and mechanical properties of 7075 aluminum alloy foam sandwich panels fabricated via integrated forming and foaming

Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited

Additive friction stir deposition of al 7075 parts and the effect of heat treatment on microstructure, electroconductivity, and mechanical properties

Development and analysis of a powder bed friction stir (PBFS) additive manufacturing process for aluminium alloys: A study on friction-stirring pitch (ω/v) and print location

A Preliminary Study on Adhesion on Steel Cylinder Filled with Aluminum Foam

An Investigation on Axial Deformation Behavior of Thin-Wall Unfilled and Filled Tube with Aluminum Alloy (Al-Si7Mg) Foam Reinforced with SiC Particles

Fabrication of Aluminum Foams with Small Pore Size by Melt Foaming Method

Effect of rotational speed and feed rate on microstructure and mechanical properties of 6061 aluminum alloy manufactured by additive friction stir deposition

Tube enhanced foam: A novel way for aluminum foam enhancement