Abstract:Improving the mechanical property of high-entropy alloys (HEAs) with face-centered cubic (fcc) structure is critical for their potential applications. In this study, the effects of substrate temperature, T sub, on nanometer-sized structure and mechanical property of fcc-structured Fe–Co–Ni–Cr–Mn HEA thin films prepared by magnetron sputtering were systematically investigated. All films grow in a nanocolumnar manner and display a single fcc-structured solid solution phase with (111) preferential orientation in addition to the reduced amorphous phase fraction and increased average grain size with increasing T sub. The top-surface cauliflower-like hierarchical microstructure with some voided boundaries for 293 K-film gradually disappears with increasing T sub up to 573 K. For higher T sub (673 K–773 K), the obvious grain growth occurs with significantly increased column size and roughness. The variations in normal hardness, H, and Young's modulus, E s, obtained from nanoindentation tests on the surface of Fe–Co–Ni–Cr–Mn HEA thin films experienced a process of first increasing and then decreasing with T sub, with a maximum at T sub = 573 K. The former increase is due to enhanced interfacial adhesion and the later decrease is ascribed to the weakened grain boundary strengthening caused by grain growth. The 573 K-film with a nanocomposite structure including hybrid nanocrystalline and amorphous phase exhibits the highest H (∼10.0 GPa) and E s (∼185.5 GPa) and is the strongest in terms of hardness among reported Fe–Co–Ni–Cr–Mn HEAs without post-treatment. In-situ micro-tensile tests alone the surface of Fe–Co–Ni–Cr–Mn HEA thin films uncovered the higher lateral yield strength (∼1.1 GPa), fracture strength (∼1.4 GPa), and Young's modulus (∼64.3 GPa) for 573 K-film than those of 293 K- and 773 K-films as well, consistent with nanoindentation results. Anisotropic mechanical responses normal to and along the surface were clearly found in Fe–Co–Ni–Cr–Mn HEA thin films, which are caused by the nanocolumnar morphology and the weakened columnar boundaries adhesion compared to the column itself.

Growth, microstructure and mechanical properties of CoCrFeMnNi high entropy alloy films

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

High hardness and fatigue resistance of CoCrFeMnNi high entropy alloy films with ultrahigh-density nanotwins

Tuning nanostructure and mechanical property of Fe–Co–Ni–Cr–Mn high-entropy alloy thin films by substrate temperature

Eutectic Growth Kinetics and Microscopic Mechanical Properties of Rapidly Solidified CoCrFeNiMo0.8 High Entropy Alloy

Fracture of Void-Embedded High-Entropy-Alloy Films: A Comprehensive Atomistic Study

High Strength and Deformation Mechanisms of Al0.3CoCrFeNi High-Entropy Alloy Thin Films Fabricated by Magnetron Sputtering

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Nanotwinned CoCrFeMnNi high entropy alloy films for flexible electronic device applications

A Dual-Phase Fe-Co-Ni-Cr-Mn High Entropy Alloy Thin Film with Superior Strength and Corrosion-Resistance

Fatigue studies of CoCrFeMnNi high entropy alloy films using nanoindentation dynamic mechanical analyses

Mechanical behavior and shear band of a powder-metallurgy-fabricated CoCrFeMnNi high-entropy alloy during high strain-rate deformation

Unique nanostructures and deformation mechanisms in a high-entropy alloy nanolaminates

Synthesis and structural characterizations of CrCoFeNiMnx (0 ≤ x ≤ 1) high-entropy-alloy thin films by thermal reduction in hydrogen

Mechanical Properties and Thermal Stability of Nanocrystalline NbMoTaW Refractory High Entropy Alloy Thin Films

Enhanced Strength of AlCoCrCu0.5FeNi High Entropy Alloy Thin Films Reinforced by Multi-Phase Hardening and Nanotwins

Size-dependent microstructural evolution and mechanical properties of crystalline/amorphous high-entropy alloy nanostructured multilayers: Cu/FeCoCrNiBSi vs Ni/FeCoCrNiBSi

Microstructure, mechanical and tribological properties of CoCrFeNi high-entropy alloy fabricated by different preparing processes

Hierarchical FeCoNiCr High Entropy Alloy Thin Films with Combined High Strength and Excellent Corrosion Resistance

High Entropy Alloy Thin Films of AlCoCrCu0.5FeNi with Controlled Microstructure

Microstructural Evolution and Strengthening Mechanisms in CrxMnFeNi High-Entropy Alloy