Abstract:Improving the mechanical property of high-entropy alloys (HEAs) with face-centered cubic (fcc) structure is critical for their potential applications. In this study, the effects of substrate temperature, T sub, on nanometer-sized structure and mechanical property of fcc-structured Fe–Co–Ni–Cr–Mn HEA thin films prepared by magnetron sputtering were systematically investigated. All films grow in a nanocolumnar manner and display a single fcc-structured solid solution phase with (111) preferential orientation in addition to the reduced amorphous phase fraction and increased average grain size with increasing T sub. The top-surface cauliflower-like hierarchical microstructure with some voided boundaries for 293 K-film gradually disappears with increasing T sub up to 573 K. For higher T sub (673 K–773 K), the obvious grain growth occurs with significantly increased column size and roughness. The variations in normal hardness, H, and Young's modulus, E s, obtained from nanoindentation tests on the surface of Fe–Co–Ni–Cr–Mn HEA thin films experienced a process of first increasing and then decreasing with T sub, with a maximum at T sub = 573 K. The former increase is due to enhanced interfacial adhesion and the later decrease is ascribed to the weakened grain boundary strengthening caused by grain growth. The 573 K-film with a nanocomposite structure including hybrid nanocrystalline and amorphous phase exhibits the highest H (∼10.0 GPa) and E s (∼185.5 GPa) and is the strongest in terms of hardness among reported Fe–Co–Ni–Cr–Mn HEAs without post-treatment. In-situ micro-tensile tests alone the surface of Fe–Co–Ni–Cr–Mn HEA thin films uncovered the higher lateral yield strength (∼1.1 GPa), fracture strength (∼1.4 GPa), and Young's modulus (∼64.3 GPa) for 573 K-film than those of 293 K- and 773 K-films as well, consistent with nanoindentation results. Anisotropic mechanical responses normal to and along the surface were clearly found in Fe–Co–Ni–Cr–Mn HEA thin films, which are caused by the nanocolumnar morphology and the weakened columnar boundaries adhesion compared to the column itself.

Synthesis and structural characterizations of CrCoFeNiMnx (0 ≤ x ≤ 1) high-entropy-alloy thin films by thermal reduction in hydrogen

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Microstructural Evolution and Mechanical Properties of Al0.3CoCrFeNiSix. High-Entropy Alloys Containing Coherent Nanometer-Scaled Precipitates

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Microstructure and Properties of FeCrMnxAlCu High-Entropy Alloys and Coatings

Mechanical properties and water vapour corrosion behaviour of Al x CoCrFeNi high-entropy alloys

Microstructures and properties of Fe1.25CoNi1.25CrxAl0.25 high-entropy alloys after cold-rolling and annealing

Effect of Mn Content on Crystallization Behaviors and Magnetic Properties of FeCoNiBMn High-Entropy Amorphous Alloys

Microstructure and properties of FeCoNiCrX (X=Mn, Al) high-entropy alloy coatings

Evaluation of the impact of Mn and Al on the microstructure of Fe–Co–Ni–Cr based high entropy alloys

Structure and Stability of High Entropy CrMnFeCoNiCu Alloy

Microstructure and Early-Stage Oxidation Behavior of Co-Cr-Cu-Fe-Mn-Ni High-Entropy Alloys

Synthesis of CoCrFeMnNi High Entropy Alloy Thin Films by Pulse Electrodeposition: Part 1: Effect of Pulse Electrodeposition Parameters

Effect of Co on phase stability and mechanical behavior of CoxCrFeNiMnAl0.3 high entropy alloys with micro/nano hierarchical structure

Microstructure and tensile properties of Co-free Fe4CrNi(AlTi) high-entropy alloys

The Microstructures and Properties Changes Induced by Al:Co Ratios of the Al CrCo FeNi High Entropy Alloys

Growth, microstructure and mechanical properties of CoCrFeMnNi high entropy alloy films

Effect of Cr Content on Microstructure, Mechanical, and Corrosion Properties of CoCr X FeMnNi High-Entropy Alloys Fabricated by Selective Laser Melting

Introducing a new heterogeneous nanocomposite thin film with superior mechanical properties and thermal stability

Tuning nanostructure and mechanical property of Fe–Co–Ni–Cr–Mn high-entropy alloy thin films by substrate temperature