Abstract:The article considers a brief review of the foreign publications on the study of the structure, phase composition and properties of five-component high-entropy alloys (HEAs) in different structural states in a wide temperature range over the past two decades. HEAs attract the attention of scientists with their unique and unusual properties. The difficulties of comparative analysis and generalization of data are noted due to different methods of obtaining HEAs, modes of mechanical tests for uniaxial compression and tension, sizes and shapes of the samples, types of thermal treatments, and phase composition (bcc and fcc crystal lattices). It is noted that the HEA with a bcc lattice has mainly high strength and low plasticity, and the HEA with a fcc lattice has low strength and increased plasticity. A significant increase in the properties of the FeMnCoCrNi HEA with a fcc lattice can be achieved by alloying with boron and optimizing the parameters of thermal mechanical treatment at alloying with carbon in the amount of 1 % (at.). The deformation curves analyzed in the temperature range –196 ÷ 800 °C indicate an increase in the yield strength with a decrease in the grain size from 150 to 5 microns. As the temperature decreases, the yield strength and elongation increase. The effect of deformation rate on the mechanical properties is an increase in the ultimate strength and yield strength, which is most noticeable at high rates of 10 –2 ÷ 10 3 s –1 . The features of HEAs deformation behavior in the mono- and poly-crystalline states are noted. The complex of high operational properties of HEAs makes it possible to use them in various industries. There are good prospects of using energy treatment to modify the surface layers and further improve HEAs properties.

Structure and Stability of High Entropy CrMnFeCoNiCu Alloy

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

Evaluation of Equiatomic CrMnFeCoNiCu System and Subsequent Derivation of a Non-Equiatomic MnFeCoNiCu Alloy

Microstructure and Mechanical Properties of Face‐Centered‐Cubic‐Based Cr‐Free Equiatomic High‐Entropy Alloys

Microstructural Study of CrNiCoFeMn High Entropy Alloy Obtained by Selective Laser Melting

Antiferromagnetism and Phase Stability of CrMnFeCoNi High-Entropy Alloy

Structure-Phase Status of the High-Entropy AlNiNbTiCo Alloy

Inner relaxations in equiatomic single-phase high-entropy cantor alloy

Investigation on structural stability of as-cast Al0.5CrCuFeMnTi high entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

On the martensitic transformation in Fe$_{x}$Mn$_{80-x}$Co$_{10}$Cr$_{10}$ high-entropy alloy

High Entropy Alloy CrFeNiCoCu sputtered films

High-entropy alloys: Structure, mechanical properties, deformation mechanisms and application

Phase equilibria in equiatomic CoCuFeMnNi high entropy alloy

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Synthesis and structural characterizations of CrCoFeNiMnx (0 ≤ x ≤ 1) high-entropy-alloy thin films by thermal reduction in hydrogen

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Controlled Valence Electron Concentration Approach to Tailor the Microstructure and Phase Stability of an Entropy-Enhanced AlCoCrFeNi Alloy

Strengthening and deformation mechanism of high-strength CrMnFeCoNi high entropy alloy prepared by powder metallurgy

Evolution of the Structure and Phase Composition of a High-Entropic CoCrFeNiCu Alloy during Prolong Annealing

Mechanical properties and fracture mechanism of as-cast MnFeCoCuNi high-entropy alloys