Abstract:The valence electron concentration (VEC) is an important physical factor for phase formation. A high VEC is conducive to forming an FCC phase and improving an alloy's ductility, while a low VEC is beneficial in forming a BCC phase that improves an alloy's strength. This is demonstrated for two HEAs, CoCrCuFeNi (FCC) and AlCoCrFeNi (BCC), that were designed as matrix alloys, where Ni and Mo are alloyed. The microstructure, phase evolution, and the mechanical properties for (AlCoCrFeNi)(100-x)Ni-x and (CoCrCuFeNi)(100-x)Mo-x were systematically investigated. As the phase structure for the (AlCoCrFeNi)(100-x)Ni-x high entropy alloy (HEA) transformed from a BCC to an FCC crystal structure as the Ni content increased from 0 at.% to 16 at.%, the FCC volume fraction increased from 0% to 85%, its compressive fracture strain increased from 25% to 40%, its VEC increased from 7.2 to 7.6. As the phase structure for the (CoCrCuFeNi)(100-x)Mo-x HEA transformed from FCC to BCC as the Mo content increased from 0 at.% to 16 at.%, the BCC volume fraction increased from 0% to 65%, its compressive yield strength increased from 260 MPa to 928 MPa, its VEC decreased from 8.8 to 8.3. Selecting an element based upon an alloy's VEC is a practical method for designing compositions for HEAs that balance strength and ductility. According to the needs of practical applications, balancing both strength and plasticity requires the following criteria for selecting an element for incorporation into an HEA system: matrix strength is improved by selecting an element with a VEC lower than the average VEC of the matrix, while ductility is improved by selecting another element with a VEC higher than the average VEC for the matrix. (C) 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Phase equilibria in equiatomic CoCuFeMnNi high entropy alloy

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Phase evolution and mechanical properties of novel FeCoNiCuMox high entropy alloys

Microstructural evolution and phase selection during solidification of AlCrCuFeNi high entropy alloy

Microstructural Evolution and Mechanical Properties of Non-Equiatomic (CoNi)74.66Cr17Fe8C0.34 High-Entropy Alloy

Evaluation of Equiatomic CrMnFeCoNiCu System and Subsequent Derivation of a Non-Equiatomic MnFeCoNiCu Alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure and Mechanical Properties of Face‐Centered‐Cubic‐Based Cr‐Free Equiatomic High‐Entropy Alloys

Phase Equilibria in the Al–Co–Cr–Fe–Ni High Entropy Alloy System: Thermodynamic Description and Experimental Study

Influence of tungsten on microstructure evolution and mechanical properties of selected novel FeCoCrMnWx high entropy alloys

Composition Design of High Entropy Alloys Using the Valence Electron Concentration to Balance Strength and Ductility

Tunable Mechanical Property and Strain Hardening Behavior of a Single-Phase CoFeNi2V0.5Mo0.2 High Entropy Alloy

Microstructural evolution of CrCuFeNiZn nanocrystalline high entropy alloy prepared by mechanical alloying

Design of non-equiatomic medium-entropy alloys

How Atomic Bonding Plays the Hardness Behavior in the Al–Co–Cr–Cu–Fe–Ni High Entropy Family

Heterogeneous Microstructure and Tensile Properties of Fe50Mn30Co10Cr10 Metastable High-Entropy Alloy

Characterization of FeCoNiCr high-entropy alloys manufactured by powder metallurgy technique

Microstructure evolution and catalytic activity of AlCo1−xFeNiTiMox high entropy alloys fabricated by powder metallurgy route

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation