Abstract:In deep underground engineering, circular roadways are widely used; many rock engineering problems can usually be simplified as mechanical analysis of rock structures with holes. To reveal the influence of intrahole reinforcement on the mechanical properties of rock with a single hole, this paper takes the single-hole rock-like material specimens with different reinforcement conditions as the research object. The RYL600 rock shear rheometer was used to conduct biaxial compression tests and, combined with HD industrial cameras and high-precision strain gauges, to study the effects of different reinforcement thicknesses and different lateral pressure on the mechanical properties of single-hole rock-like materials during the total stress and strain process. The thickness of the reinforced aluminum alloy pipe in the whole test is divided into four types: 0, 1, 1.5, and 2 mm. Under different reinforcement conditions, it is divided into 4 series of 0, 0.5, 1, and 1.5 MPa according to the different lateral pressure. Research shows the following: (1) Under the same lateral pressure, as the reinforcement thickness of the aluminum alloy tube increases, the reinforcement effect of the aluminum alloy tube on the specimen increases, and the strength of the reinforced specimen is increased by 1.42%~33.04% compared with the strength of the unreinforced specimen; under the same reinforced thickness of the aluminum tube, the peak strength of the specimen increases with the increase of lateral pressure, and the peak strength of the specimen with lateral pressure is 3.34%~50.26% higher than that of the specimen without lateral pressure. (2) Increasing the lateral pressure can significantly reduce the primary tensile cracks of the specimen. As the reinforcement thickness increases, the primary tensile cracks and remote cracks of the specimen are significantly reduced, and the failure surface of the specimen gradually tends to the middle of the sample. (3) The failure modes of specimens with holes can be divided into five types: single bevel type I, single bevel type II, single bevel type III, bevel T type, and single part shear type. All of these five failure modes are shear cracks that develop into fracture surfaces, while remote cracks and primary tensile cracks do not develop into fracture surfaces.

Experimental study on the influence of bending and straightening cycles for non-destructive and destructive coiled tubing

Low-Cycle Fatigue Test of Circular Concrete Filled Tubular Columns

Low-Cycle Fatigue Damage of Circular Concrete-Filled-Tube Columns

Experimental and numerical simulation study on fatigue life of coiled tubing with typical defects

Research on CFRP confined circular concrete-filled steel tubular columns subjected to cyclic lateral forces

Improved Ultra-Low Cycle Fatigue Fracture Models for Structural Steels Considering the Dependence of Cyclic Damage Degradation Parameters on Stress Triaxiality

Flexural behavior of concrete-filled circular steel tubes under high-strain rate impact loading

Effect of microstructure on fatigue crack initiation and propagation behavior of coiled tubing during in-situ cyclic loading

Study on Erosion Model Optimization and Damage Law of Coiled Tubing

Deformation and damage of cement sheath in gas storage wells under cyclic loading

Fatigue investigation of tubing string in high-yield curved wells

EXPERIMENTAL STUDY ON CENTRIFUGAL CONCRETE-FILLED STEEL TUBES UNDER BENDING AND TORSION

Fatigue failure mechanism of 3D tubing strings used in high-pressure, high-temperature and high-yield curved gas wells

Orthogonal wear experiment of 13Cr-L80 tubing string in high-yield gas wells and analysis of its influencing factors

Experimental study on centrifuge concrete filled thin-walled steel tubular components under the action of torsion

Experimental Studies on Cracking and Local Strain Behaviors of Rock-Like Materials with a Single Hole before and after Reinforcement under Biaxial Compression

Strain and pore pressure development on soft marine clay in triaxial tests with a large number of cycles

Local Damage Identification of High-Strength Circular Concrete-Filled Steel Tubes under Low Cycle Fatigue

Offshore Oilfield Gas Injection Wells Erosion Study and Evaluation

Bending Ratcheting Behavior of Pressurized Straight Z2CND18.12N Stainless Steel Pipe

Friction-wear failure mechanism of tubing strings used in high-pressure, high-temperature and high-yield gas wells