Abstract:Cement-based cementitious materials occupy a central position in the construction industry, but the problem of high carbon dioxide(CO2) emissions from cement production has attracted global attention. To meet this challenge, finding low-carbon alternative materials has become a top priority in the research of new building materials. At the same time, the problem of large amounts of lithium slag piling up needs to be solved, and resource utilization has become its potential way out. In this study, the volcanic ash activity of lithium slag was activated by composite activation means of high-temperature calcination and sodium silicate, and it was used as an alternative mix to cement. The Box–Behnken design and response surface method (BBD-RSM) was utilized to optimize the ratio of activated lithium slag composite cement-based cementitious materials, and high-performance new solid waste cementitious materials were prepared. The results show that activated lithium slag composite cementitious materials activated lithium slag exhibit excellent performance when activated lithium slag mass fraction is 7.3%, the sodium silicate dosage is 8.8%, and water–solid ratio is 0.6:1. The composite cementitious material under this ratio shows excellent performance, with fluidity 235.69 mm, gelation time 73.54 s, water evolution rate 1.123%, 3d and 28d compressive strengths, respectively, are 11.54 MPa and 22.9 MPa. Compared with ordinary Portland-cement-based cementing materials, the uniaxial compressive strength, modulus of elasticity, and tensile strength at break of activated lithium slag cementitious material solidified body were increased by 34.33%, 36.43%, and 34.98%, and the compressive deformation and tensile deformation were enhanced by 37.78% and 40%. This study not only provides a theoretical basis and experimental foundation for the preparation of new solid waste cementitious materials, but also provides a new solution for the reinforcement of crushed rock bodies in engineering practice, which is of great significance for promoting the low-carbon development of the construction industry.

What problem does this paper attempt to address?

The paper primarily aims to address the following two key issues: 1. **Finding low-carbon alternative materials to reduce CO2 emissions during cement production**: Given the significant environmental impact of the high amount of CO2 generated during cement production, researchers are striving to find new materials that can replace or partially replace traditional cement to reduce carbon emissions, achieve high-quality development in the construction industry, and meet carbon neutrality goals. 2. **Utilizing lithium slag as an effective way to manage industrial waste**: With the rapid development of the new energy vehicle market and advancements in lithium battery technology, the production of lithium slag has increased dramatically. Currently, the global utilization rate of lithium slag is extremely low, with most of it being disposed of through traditional methods such as piling or landfilling, which not only wastes resources but also causes environmental pollution. Therefore, effectively utilizing lithium slag has become an urgent issue to address. To solve the above problems, the study adopted the following methods: - **Activating the pozzolanic activity of lithium slag**: By using high-temperature calcination and composite activation with water glass, the pozzolanic activity of lithium slag was enhanced, and it was used as a partial replacement for cement. - **Optimizing the proportion formula**: Using Box-Behnken Design and Response Surface Methodology (BBD-RSM) to optimize the proportion of activated lithium slag composite cementitious materials, high-performance new solid waste cementitious materials were prepared. Experimental results showed that when the mass fraction of lithium slag was 7.3%, the amount of water glass was 8.8%, and the water-solid ratio was 0.6:1, the activated lithium slag composite cementitious material exhibited excellent performance. Compared to ordinary Portland cement cementitious materials, the compressive strength, elastic modulus, and fracture tensile strength of the solidified body increased by 34.33%, 36.43%, and 34.98%, respectively, and the compressive deformation and tensile deformation capabilities were also enhanced. This study not only provides a theoretical basis and experimental foundation for the preparation of new solid waste cementitious materials but also offers a new solution for reinforcing fractured rock masses in engineering practice. It is of great significance for promoting low-carbon development in the construction industry.

Experimental Study Based on Box–Behnken Design and Response Surface Methodology for Optimization Proportioning of Activated Lithium Slag Composite Cement-Based Cementitious Materials

Sustainable Building Material from CO2 Mineralization Slag: Aggregate for Concretes and Effect of CO2 Curing

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Study on the Alkali–Sulfur Co-Activation and Mechanical Properties of Low-Carbon Cementitious Composite Materials Based on Electrolytic Manganese Residue, Carbide Slag, and Granulated Blast-Furnace Slag

Microstructures and properties of alkali-activated slags with composite activator: Effects of Na2O equivalents

Study on the Properties and Hydration Mechanism of Calcium Carbide Residue-Based Low-Carbon Cementitious Materials

Study on the preparation, performance, and mechanism for solid waste cementitious materials

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Research Progress on the Activity Stimulation of Lithium Slag in Concrete

Preparation of Cementitious Materials from Mechanochemically Modified Copper Smelting Slag Compounded with High-Aluminum Fly Ash

Study on the Performance of Recycled Cement-Stabilized Macadam Mixture Improved Using Alkali-Activated Lithium Slag–Fly Ash Composite

Innovative synthesis of low-carbon cemented backfill materials through synergistic activation of solid wastes: An integrated assessment of economic and environmental impacts

Enhancement of ultra-fine slag on compressive strength of solid waste-based cementitious materials: Towards low carbon emissions

Synergistic Activation Mechanism and Long-Term Properties of a Solid Waste Cementitious Materials Based on Red Mud and Calcium Carbide Slag

The Use of Slag and Red Mud for the Synthesis of a Slag-Based Cementitious Material

Optimization of Proportions and Solidification Mechanism of All-Solid Waste Cementitious Materials Based on Circulating Fluidized Bed Fly Ash, Calcium Carbide Slag, and Red Mud

Preparation for micro-lithium slag via wet grinding and its application as accelerator in Portland cement

Effect of Mineral-Generated Lithium Slag on the Properties of Magnesium Oxychloride Cement

Research Progress of Low-Carbon Cementitious Materials Based on Synergistic Industrial Wastes

Design and Preparation Technology of Green Multiple Solid Waste Cementitious Materials

The Effect of μ-Limestone Additions on the Mechano-Chemical and Microstructural Properties of Slag and Binary Slag/Ground Fly Ash Alkaline-Activated Binders