Abstract:As the main gel material of concrete, cement is used in an astonishing amount every year in the construction industry. However, a large amount of CO 2 is emitted into the atmosphere while producing cement. Therefore, it is the general trend to look for substitutes for cement and develop new green concrete. Lithium slag (LS) is the industrial waste discharged from lithium salt plants. Through testing, it is found that the chemical composition of LS has a high degree of coincidence with ordinary Portland cement (OPC) Therefore, LS can be incorporated into concrete as supplementary cementations material (SCM) to prepare lithium slag concrete (LSC). The pollution of the natural environment caused by a large number of piled-up and landfilled LS is immeasurable. Consuming and using LS in large quantities and with high efficiency not only eliminates the pollution of lithium slag to the natural environment, but also helps to reduce the amount of cement used in green concrete and truly reuse waste resources. In order to study the mechanical properties of post-heated LSC, the test were carried out for LSC specimens after high-temperature. The main influence factors were considered, including the temperatures of 20°C, 100 °C, 300 °C, 500 °C and 700 °C, the contents of lithium slag in LSC of 0%, 10%, 20% and 30%, cooling method of LSC after exposure high temperature. The results showed that the mechanical properties of LS concrete specimens were slightly improved at 100 °C, and when the temperature was 300 °C or higher, the damage to the specimens was huge and irreversible. An appropriate amount of LS (20% lithium slag content) could improve the strength of LSC. This paper also studied the relationship between lithium slag content and strengths of LS concrete. The research results show that adding an appropriate amount of LS to concrete improves the mechanical properties of concrete. When the LS replacement rate is 20%, the mass loss rate of LSC after different high temperature treatments was the minimum. The cubic compressive strength, axial compressive strength, and flexural strength of specimens with 20% LS substitution can be increased by 8.16%, 8.33%, and 13.46% after high temperature. The cubic compressive strength, axial compressive strength, and flexural strength of specimens with 20% LS substitution can be increased by 8.16%, 8.33%, and 13.46% after high temperature.

Preparation for micro-lithium slag via wet grinding and its application as accelerator in Portland cement

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Research Progress on the Activity Stimulation of Lithium Slag in Concrete

Experimental Study Based on Box–Behnken Design and Response Surface Methodology for Optimization Proportioning of Activated Lithium Slag Composite Cement-Based Cementitious Materials

Effect of Mineral-Generated Lithium Slag on the Properties of Magnesium Oxychloride Cement

Experimental Study on the Preparation of Cementitious Materials Through the Activation of Lead—Zinc Tailings

A Review on Cementitious and Geopolymer Composites with Lithium Slag Incorporation

Fresh, mechanical, and microstructural properties of lithium slag concretes

Understanding the Utilization Potential of Lepidolite Slag in Cementitious Materials: Composition Characteristics, Hydration Properties, and High Value-Added Cementitious System Design

Iron ore tailings, phosphate slags, and lithium slags as ternary supplementary cementitious materials for concrete: Study on compression strength and microstructure

High performance C-A-S-H seeds from fly ash-carbide slag for activating lithium slag towards a low carbon binder

Utilization of carbide slag-granulated blast furnace slag system by wet grinding as low carbon cementitious materials

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Laboratory Preparation and Performance Characterization of Steel Slag Ultrafine Powder Used in Cement-Based Materials

Research on the High Performance of Concrete Mixed with Lithium Slag in Hydraulic Structures

Lithium Slag and Solid Waste-Based Binders for Cemented Lithium Mica Fine Tailings Backfill

Enhancement of ultra-fine slag on compressive strength of solid waste-based cementitious materials: Towards low carbon emissions

Deep insight into mechanical behavior and microstructure mechanism of quicklime-activated ground granulated blast-furnace slag pastes

Preparation of Cementitious Materials from Mechanochemically Modified Copper Smelting Slag Compounded with High-Aluminum Fly Ash

Microstructures and properties of alkali-activated slags with composite activator: Effects of Na2O equivalents

Effect of high temperature on mechanical properties of lithium slag concrete