Abstract:Currently, there is a scarcity of studies exploring the safe operating parameters for coal-fired power units at loads below 30%.To accurately understand the operating characteristics of coal-fired units under low load conditions, and to provide a design basis for flexibility modifications, a simulation model coupled with boiler and turbine was established, which includes the flue gas and air system, steam and water system, steam turbine, and steam extraction heat recovery system, and the iterative calculation strategy for low load conditions was proposed. The simulation calculation was performed on a 350 MW supercritical coal-fired unit, with the model results showing a high degree of alignment with the unit’s design and operational parameters. Under the condition of 269MW, the maximum calculation error between the model’s predicted exit flue gas temperature of the air preheater and the actual operational results was 8.84%. This discrepancy was due to a sudden increase in the operating flue gas temperature, which may be associated with a blockage in the air preheater. And the simulation results under low load conditions indicate that when the unit load is below 20%, the furnace total airflow is controlled to no less than 30% of the airflow at Maximum Continuous Rating (BMCR) and the minimum feedwater flow rate can be reduced to 20% of that in Turbine Heat Acceptance (THA) load, and the unit switches to wet state operation around 20% load. As the unit load decreases, the coal consumption rate for power generation and steam turbine heat consumption rate both increase significantly. The coal consumption rate for power generation at 30% load is increased by 13.3% compared to BMCR load, and it is increased by 32.5% at 15% load which is operated in wet state. Under low load conditions, the coal consumption rate of the unit can be reduced by decreasing the oxygen content in the flue gas, reducing the minimum feedwater flow rate, and implementing boiler water recirculation.

Hydrodynamic Analysis and Metal Temperature Calculation for the Water Wall of a 660MW Supercritical Boiler at Severe Peak Load Regulation

Computational analysis on hydrodynamic characteristics and flow instability of an ultra supercritical 1000 MW double-reheat unit boiler

Investigation on Hydrodynamic Performance and Wall Temperature of Water-Cooled Wall in 1000 MW Boiler Under Low-Load Conditions

ICOPE-15-C004 Thermal-hydraulic Analysis and Metal Temperature Computation for the Water Wall of a 1000MW Ultra Supercritical Tower Boiler with Double Reheat

Analysis on the Steam Temperature Deviation of the Vertical Water Wall and the Adjustment Plan of the Throttle Ring for an Ultra-supercritical Boiler

Thermal-Hydraulic Calculation and Analysis on Evaporator System of a 1000 MW Ultra-Supercritical Pulverized Combustion Boiler with Double Reheat

Steam Temperature Characteristics in Boiler Water Wall Tubes Based on Furnace CFD and Hydrodynamic Coupling Model

Safety analysis of operation of water walls of a 300 MW once-through boiler in peak load operation

Dynamic Analysis for Ultra-Supercritical Boiler Water Wall Considering Uneven Heat Flux Distribution and Combustion Instability

A Real-Time Calculation Method to Improve Boiler Safety in Deep Peak Shaving Cases

Tube-Wall Temperature Prediction of a 660-MW Ultra-Supercritical Double-Reheat Boiler under Flexible Peak Shaving

Thermal–Hydraulic Calculation and Analysis on Water Wall System of a 700 MWe Ultra-Supercritical CFB Boiler

Hydrodynamic characteristic calculation for a 600 MW unit onceGthrough tower boiler

Research on the Hydrodynamic Characteristics and Metal Temperature Distribution in Spiral Tube Water Wall of an Ultra Supercritical Boiler

Water wall temperature deviation of an ultra-supercritical 1000 MW unit boiler: analysis and countermeasures

Simulation of low-load operation for a 350 MW supercritical unit

Mathematical modeling and thermal-hydraulic analysis of vertical water wall in an ultra supercritical boiler

Calculation on Flow Rate Distribution and Wall Temperature of Waterwall with Spiral Tube Coils of Supercritical Once-through Boilers

Heat Transfer in Furnace of 1 000 MW Coal-fired Unit under Different Load Conditions

Hydrodynamic analysis and calculation of metal temperature distribution in spiral water wall of ultra supercritical tower boiler

ICOPE-15-C136 Study on Temperature Characteristics of Water Wall in 700℃ Ultra Supercritical Boiler