Abstract:It is irrefutable that the presence of hydrogen reduces the mechanical performance of many metals and alloys used for structural components. Several mechanisms of hydrogen-assisted cracking (HAC) of steels have been postulated. The direct evidence of the mechanisms by which hydrogen embrittles these materials has remained elusive. This is by virtue of our difficulty to directly observe the hydrogen distribution at spatial resolutions less than 100 nm and analysis volumes greater than 1 × 109 atoms at microstructural features such as grain boundaries, dislocations, twins, stacking faults and sub-micron inclusions that are all potential hydrogen trapping sites postulated to be responsible for the degradation of mechanical performance. Here, we report on an experimental methodology combining an elaborate fatigue testing protocol in an enriched gaseous deuterium environment with NanoSIMS (secondary ion mass spectrometry) imaging for detection of deuterium at spatial resolutions as low as 100 nm and accompanying TEM analysis. Type 316 stainless steel compact tension specimens were precharged in deuterium followed by fatigue testing at high stress ratio (0.7), low delta K (~11 MPa √m), and a frequency of 1 cycle per minute using a sawtooth waveform with a rise time of 30 s in high pressure (68.9 MPa) gaseous deuterium (99.999% purity) environment at room temperature. High resolution NanoSIMS imaging was then used to measure the deuterium distribution at the tip of and in the wake of secondary and tertiary fatigue cracks as well as at MnS inclusions. The use of deuterium eliminates the difficulties of interpreting hydrogen measurements by SIMS relating to the ubiquitous presence of hydrogen in all high vacuum systems and guarantees that deuterium measured by the NanoSIMS must be attributed to the fatigue testing protocol. This methodology has allowed us to directly observe the distribution of hydrogen in dislocation tangles ahead and in the wake of fatigue crack tips and at the interface of MnS inclusions. The protocol provides an avenue by which the path and speed with which hydrogen proceeds along its embrittling course of action may be directly followed through modifications of the fatigue testing parameters and/or alloy type and allows a means to validate at least qualitatively recently published models of enhanced hydrogen transport by dislocations.

Hydrogen and deuterium charging of site-specific specimen for atom probe tomography

Hydrogen and deuterium charging of lifted-out specimens for atom probe tomography

Optimizing site-specific specimen preparation for atom probe tomography by using hydrogen for visualizing radiation-induced damage

Quantification challenges for atom probe tomography of hydrogen and deuterium in Zircaloy-4

Towards establishing best practice in the analysis of hydrogen and deuterium by atom probe tomography

Towards Quantitative Analysis of Deuterium Absorption in Ferrite and Austenite during Electrochemical Charging by Comparing Cyclic Voltammetry and Cryogenic Transfer Atom Probe Tomography

Solute hydrogen and deuterium observed at the near atomic scale in high-strength steel

Characterization of hydrogen traps in a co-precipitation steel investigated by atom probe experiments without cryogenic transfer

Atom Probe Analysis of Ex Situ Gas-Charged Stable Hydrides

In Situ Pulsed Hydrogen Implantation in Atom Probe Tomography

Atom Probe Tomographic Observation of Hydrogen Trapping at Carbides/ferrite Interfaces for a High Strength Steel

Application of atom probe tomography to fundamental issues of steel materials

High resolution NanoSIMS imaging of deuterium distributions in 316 stainless steel specimens after fatigue testing in high pressure deuterium environment

Observation of Hydrogen Trapping at Dislocations, Grain Boundaries, and Precipitates

Assessment of the Potential of Hydrogen Plasma Charging As Compared to Conventional Electrochemical Hydrogen Charging on Dual Phase Steel

Miniaturized gas exposure devices for atom probe experiments

Interaction Between Dislocations, Precipitates and Hydrogen Atoms in a 2000 MPa Grade Hot-Stamped Steel

Correlative Site-Specific Sample Preparation for Atom Probe Tomography on Complex Microstructures

In-situ 3D Observation of Hydrogen-Assisted Particle Damage Behavior in 7075 Al Alloy by Synchrotron X-ray Tomography