Abstract:Tin monosulfide can be grown in cubic (pi-SnS) and orthorhombic (alpha-SnS) polymorphs by low-temperature atomic layer deposition (ALD). The optical properties of these polymorphs make them attractive for the realization of plasmonic solar cells with ultrathin absorber layers down to 10 nm in thickness. SnS is also an earth-abundant and nontoxic compound semiconductor of high interest for regular thin-film photovoltaics. To better understand the behavior of the two SnS polymorphs in ultrathin solar cell configurations, we here fabricate, characterize, and analyze a range of such devices. ALD is used to grow SnS and form heterojunctions with zinc oxysulfide [Zn(O,S)], acting as a buffer layer with a composition-tunable bandgap. Apart from the roles of the SnS polymorph and Zn(O,S) composition, the effects of the back contact material and thicknesses of buffer and absorber layers are investigated. Devices using pi-SnS and pure ZnO buffers yield the highest photocurrents (3.1 mA/cm(2)) and higher open circuit voltage (159 mV) than similar alpha-SnS-based devices. Analysis of the equivalent-circuit parameters suggests that interface recombination limits the voltage for these devices. While Zn(O,S) with a higher sulfur content provides chemical passivation of the SnS interface and excessive open circuit voltages above 600 mV, it also exhibits a too high conduction band offset, which hampers current collection. A growth delay during the ALD of Zn(O,S) on SnS initially amplifies the known sulfur-oxygen exchange reaction, such that a sulfur-rich Zn(O,S) region forms next to the SnS interface. This causes a thin ZnS-like barrier to form already for low cycle fractions of the H2S precursor in the ALD super-cycle. Voltage and fill factor trends suggest an optimal SnS absorber layer thickness in the range of 15-35 nm, presenting an opportunity for plasmonic absorption enhancement. Devices with pi-SnS show most promise, but interface recombination versus current-blocking is a dilemma for the SnS/Zn(O,S) heterojunction.

Fabrication of (Ge0.42Sn0.58)S Thin Films via Co-Evaporation and Their Solar Cell Applications

Fabrication of Cu2Sn1-xGexS3 Thin-Film Solar Cells via Sulfurization of Cu2GeS3/Cu2SnS3 Stacked Precursors

Stable SnS x Se 1−x /CdS thin-film solar cells via single-source vapor transport deposition: unveiling band alignment at heterojunction interface

Thin films of tin sulphide for use in thin film solar cell devices

Thin Films Of Tin Sulphide For Application In Photovoltaic Solar Cells

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

Tin Sulphide Thin Films Synthesised Using a Two Step Process

Single Phase, Large Grain, p-Conductivity-type SnS Layers Produced using the Thermal Evaporation Method

Fabrication of Cu 2 SnS 3 thin-film solar cells with oxide precursor by pulsed laser deposition

Sulfurization Growth of SnS Thin Films and Experimental Determination of Valence Band Discontinuity for SnS-Related Solar Cells

Fabrication of solar cells based on $Cu_2ZnSnS_4$ prepared from $Cu_2SnS_3$ synthesized using a novel chemical procedure

Single-source Thermal Evaporation Converts Anion Controllable Sb 2 (s,se) 3 Film for Fabricating High-Efficiency Solar Cell

Evaluation of AA-CVD deposited phase pure polymorphs of SnS for thin films solar cells

Sb-2(Se1-xSx)(3) Thin-Film Solar Cells Fabricated by Single-Source Vapor Transport Deposition

Fabricating over 7%-efficient Sb2(S,Se)3 thin-film solar cells by vapor transport deposition using Sb2Se3 and Sb2S3 mixed powders as the evaporation source

Sequential Coevaporation and Deposition of Antimony Selenosulfide Thin Film for Efficient Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Fabrication of highly crystallized Cu 2 SnS 3 thin films through sulfurization of Sn-rich metallic precursors

Improving the performance of low-cost water-based solution-synthesised Cu2ZnSn1-Ge (S,Se)4 absorber thin films by germanium doping

Ultrathin Solar Cells Based on Atomic Layer Deposition of Cubic Versus Orthorhombic Tin Monosulfide