Abstract:Galvanizing is the process of applying a protective zinc or zinc alloy coating to steel or iron which acts as a sacrificial anode to protect the underlying steel or iron. These coatings are mainly used in the automotive and construction industry where corrosive environments will be encountered. There has been a drive to improve the performance of galvanised coatings through alloy additions, initially Al (5 – 55 wt%) and more recently through the development of Zn - Al - Mg coatings. Here, Al and Mg are added as minority additions (typically 1 - 3 wt %) to improve corrosion resistance allowing thinner coatings to be used thus saving material, weight and cost. The assessment of the corrosion performance of such coatings is often evaluated through standardised tests. An industry standard test known as Prohesion or ASTM G85 Annex A5 is carried out on metallic coatings as it is thought to better represent long-term natural exposure than a regular salt spray test. The Prohesion test is a cyclic accelerated corrosion test using an electrolyte of 0.4% Ammonia sulphate and 0.05% sodium chloride (NaCl). This investigation aims to determine the effects on the corrosion performance of zinc-aluminium alloys and zinc-aluminium-magnesium alloys of varying compositions immersed in Prohesion solution. Previous work on this topic suggests that magnesium containing alloys were particularly susceptible to accelerated corrosion in Prohesion solution. Here, several zinc based alloys were immersed in Prohesion solution as well as a control 0.45% sodium chloride solution and subjected to electrochemical testing. The electrochemical techniques used to test said substrates are linear polarisation resistance (LPR), scanning vibrating electrode technique (SVET) and time-lapse optical microscopy (TLM) all for 24 hours. The alloys that underwent testing are shown in Table 1. Table 1: Table showing the composition of substrates used. Sample number Composition 1 Zn-<0.2wt%Al 2 Zn-5wt%Al 3 Zn-55wt%Al 4 Zn-1.2wt%Al-Zn1.2wt%Mg 5 Zn-3.5wt%Al-3wt%Mg 6 Zn-6wt%Al-3wt%Mg The results from the TLM showed differences in the corrosion mechanism that is dependent on the alloy composition and electrolyte. Generally, all substrates immersed in the control 0.45% NaCl showed localised corrosion with distinct anodes developing surrounded by a ring of corrosion product and white rust is observed on the surface of the substrate. The initial site of anodic attack in the microstructure was dependent on the alloy composition. However, when immersed in the Prohesion solution significant differences were observed dependent on the alloy composition. For Zn-Al-Mg coatings rapid attack of zinc-magnesium phases was observed especially in the eutectic regions followed by aggressive attack of the entire exposed surface of the alloy within 6 hours. Additionally, no corrosion product rings formed. For Zn-Al alloy coatings, the zinc phases were preferentially attacked with the aluminium containing phases appearing to be resistant to corrosion during the duration of the tests. No white rust was seen on the surface of the substrates and instead a dark surface/corrosion product film was observed. The corrosion rate from the LPR data measured at hourly intervals over 24 hours increases when substrates are immersed in Prohesion solution compared to NaCl, with the most noticeable increase seen when there are zinc-magnesium phases present within the alloy. The largest increase in corrosion rate mm per year (mmpy) was seen in sample 5 with it increasing from 0.15 mmpy after 24 hours in the control solution to 0.55 mmpy in the Prohesion solution after 24 hours. The same is observed with the SVET results showing that the ammonium ions are having a significant damaging effect on the Zn-Al-Mg metallic coatings. The proposed corrosion mechanism for Zn-Al-Mg alloy coatings in Prohesion solution is preferential dissolution of MgZn 2 in eutectic phases due to reactivity of Mg producing Mg(OH) 2 which is a highly basic hydroxide. Due to the basic nature of Mg(OH) 2 , Ammonium (NH 4 + ) cations react with Mg(OH) 2 producing Mg 2+ and Ammo -Abstract Truncated-

Electrochemical Evaluation of Al-5 wt% Zn Metal Rich Primer for Protection of Al-Zn-Mg-Cu Alloy in NaCl

Electrochemical Evaluation of Mg and a Mg-Al 5%Zn Metal Rich Primers for Protection of Al-Zn-Mg-Cu Alloy in NaCl

Mechanistic Insight into Al-Zn, Mg, and Al-Mg Rich Primer Design for Enhanced Cathodic Prevention on Sensitized Al-Mg Alloys

Corrosion Behavior of Al Modified with Zn in Chloride Solution

The long‐term corrosion performance and adhesion properties of 7B04 aluminum alloy/anodic film/epoxy primer system in acidic NaCl solution

Complementary corrosion protection of cast AlSi7Mg0.3 alloy using Zr-Cr conversion and polyacrylic/siloxane-silica multilayer coatings

Microstructural characterization and corrosion resistance evaluation of chromate-phosphate/water-soluble resin composite conversion coating on Al surfaces

The Effect of Ammonium Ions on the Corrosion Resistance of Zinc - Aluminium and Zinc - Aluminium - Magnesium Coated Steel

Anticorrosive chromium free primers for aluminium alloys: application in the aerospace industry

Study of ZnAl Hydroxides-Based Thin Films to Enhance the Filiform Corrosion Resistance of Acrylic-Coated AA5005

Comparative Study of Carbonaceous and Polymer Conductive Additives on Anticorrosion Performance of Epoxy Zinc-Rich Primer

Effect of Al Content on the Long-Term Corrosion Behavior of Arc-Sprayed ZnAl Alloy Coatings

Electrochemical Behavior of Organic and Inorganic Zinc-Rich Coatings in 3.5% NaCl Solution

Anticorrosive Performance Approach Combining an Epoxy Polyaminoamide–Zinc Phosphate Coatings Applied on Sulfo-tartaric Anodized Aluminum Alloy 5086

The Role of Zinc Phosphate Pigment in the Anticorrosion Properties of Bisphenol A Diglycidyl Ether-Polyaminoamide Coating for Aluminum Alloy AA2024-T3

Study of the physical and electrochemical properties of hybrid paint system based on zinc-rich primer for mild steel protection

The Effect Spray Testing Condition on the Corrosion Performance of Hydrothermally Sealed Anodic Oxide on a 5005 Aluminum Alloy: Comparison between Neutral Salt Spray, Acetic Salt Spray and Prohesion Testing Methods

Inhibitor pretreatment synergies demonstrated using a scanning Kelvin probe technique

Corrosion and Stress Corrosion Resistance of Al Zn Alloy 7075 by Nano-Polymeric Coatings

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution