Abstract:Galvanizing is the process of applying a protective zinc or zinc alloy coating to steel or iron which acts as a sacrificial anode to protect the underlying steel or iron. These coatings are mainly used in the automotive and construction industry where corrosive environments will be encountered. There has been a drive to improve the performance of galvanised coatings through alloy additions, initially Al (5 – 55 wt%) and more recently through the development of Zn - Al - Mg coatings. Here, Al and Mg are added as minority additions (typically 1 - 3 wt %) to improve corrosion resistance allowing thinner coatings to be used thus saving material, weight and cost. The assessment of the corrosion performance of such coatings is often evaluated through standardised tests. An industry standard test known as Prohesion or ASTM G85 Annex A5 is carried out on metallic coatings as it is thought to better represent long-term natural exposure than a regular salt spray test. The Prohesion test is a cyclic accelerated corrosion test using an electrolyte of 0.4% Ammonia sulphate and 0.05% sodium chloride (NaCl). This investigation aims to determine the effects on the corrosion performance of zinc-aluminium alloys and zinc-aluminium-magnesium alloys of varying compositions immersed in Prohesion solution. Previous work on this topic suggests that magnesium containing alloys were particularly susceptible to accelerated corrosion in Prohesion solution. Here, several zinc based alloys were immersed in Prohesion solution as well as a control 0.45% sodium chloride solution and subjected to electrochemical testing. The electrochemical techniques used to test said substrates are linear polarisation resistance (LPR), scanning vibrating electrode technique (SVET) and time-lapse optical microscopy (TLM) all for 24 hours. The alloys that underwent testing are shown in Table 1. Table 1: Table showing the composition of substrates used. Sample number Composition 1 Zn-<0.2wt%Al 2 Zn-5wt%Al 3 Zn-55wt%Al 4 Zn-1.2wt%Al-Zn1.2wt%Mg 5 Zn-3.5wt%Al-3wt%Mg 6 Zn-6wt%Al-3wt%Mg The results from the TLM showed differences in the corrosion mechanism that is dependent on the alloy composition and electrolyte. Generally, all substrates immersed in the control 0.45% NaCl showed localised corrosion with distinct anodes developing surrounded by a ring of corrosion product and white rust is observed on the surface of the substrate. The initial site of anodic attack in the microstructure was dependent on the alloy composition. However, when immersed in the Prohesion solution significant differences were observed dependent on the alloy composition. For Zn-Al-Mg coatings rapid attack of zinc-magnesium phases was observed especially in the eutectic regions followed by aggressive attack of the entire exposed surface of the alloy within 6 hours. Additionally, no corrosion product rings formed. For Zn-Al alloy coatings, the zinc phases were preferentially attacked with the aluminium containing phases appearing to be resistant to corrosion during the duration of the tests. No white rust was seen on the surface of the substrates and instead a dark surface/corrosion product film was observed. The corrosion rate from the LPR data measured at hourly intervals over 24 hours increases when substrates are immersed in Prohesion solution compared to NaCl, with the most noticeable increase seen when there are zinc-magnesium phases present within the alloy. The largest increase in corrosion rate mm per year (mmpy) was seen in sample 5 with it increasing from 0.15 mmpy after 24 hours in the control solution to 0.55 mmpy in the Prohesion solution after 24 hours. The same is observed with the SVET results showing that the ammonium ions are having a significant damaging effect on the Zn-Al-Mg metallic coatings. The proposed corrosion mechanism for Zn-Al-Mg alloy coatings in Prohesion solution is preferential dissolution of MgZn 2 in eutectic phases due to reactivity of Mg producing Mg(OH) 2 which is a highly basic hydroxide. Due to the basic nature of Mg(OH) 2 , Ammonium (NH 4 + ) cations react with Mg(OH) 2 producing Mg 2+ and Ammo -Abstract Truncated-

The Effect Spray Testing Condition on the Corrosion Performance of Hydrothermally Sealed Anodic Oxide on a 5005 Aluminum Alloy: Comparison between Neutral Salt Spray, Acetic Salt Spray and Prohesion Testing Methods

Study of ZnAl Hydroxides-Based Thin Films to Enhance the Filiform Corrosion Resistance of Acrylic-Coated AA5005

Influence of Acid Pickling on Electrodeposition of Aluminum on Magnesium Alloy in Room Temperature Molten Salts

Salt Spray (Fog) Corrosion Behavior of Cold-Sprayed Aluminum Amorphous/Nanocrystalline Alloy Coating

Study on the Influence of Surface Treatment Process on the Corrosion Resistance of Aluminum Alloy Profile Coating

Influence of Formation Conditions on Corrosion Behavior of PEO-Coatings during Salt-Spray Test

Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments

Effect of Different Sealing Treatments of Oxide Films on Corrosion Resistance of Anodized ZL101A Aluminum Alloy in Simulated Marine Atmospheric Environment

COMPARISON OF TWO STAINING METHODS FOR ANODIZING IN ALLOY 6063 ALUMINUM PROFILES

Interface strength and degradation of adhesively bonded porous aluminum oxides

Corrosion Inhibitor Screening For Aa6014 Aluminum Alloy Under Different Ambient Conditions Using A Novel Multielectrode Methodology

Hydrothermal and cerium salt sealing of a 6061 aluminum alloy

Characterization of the Anodic Film and Corrosion Resistance of an A535 Aluminum Alloy after Intermetallics Removal by Different Etching Time

Microstructural and Electrochemical Study: Pitting Corrosion Mechanism on A390 Al–Si Alloy and Ce–Mo Treatment as a Better Corrosion Protection

Investigation of Long-term Corrosion of AA2024 and AA5119 Aluminum Alloys under chromate coating in Marine Atmosphere by Electrochemical Impedance Technology

Effect of post-sealing treatment with different concentrations of NaH2PO4 on corrosion resistance of MAO coating on 6063 aluminum alloy

Improving the Corrosion Behaviour of 6061 Aluminum Alloy by Controlled Anodic Formed Oxide Layer

The Effect of Ammonium Ions on the Corrosion Resistance of Zinc - Aluminium and Zinc - Aluminium - Magnesium Coated Steel

Study on the effect of acetate ions on the sealing treatment for anodic oxide film of 6063 aluminum alloy

Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys

High Rate Mechanical Characterization of Sensitized 5083-H131 Aluminum Alloy