Abstract:The automotive industry is constantly striving for targets for the development of lightweight materials for less fuel consumption and carbon emissions. For this purpose, lighter and higher-performance Al-Si alloys with high service life are preferred in mechanical systems to increase fuel efficiency. However, uncertainties regarding the mechanical and machining properties of these alloys continue in the industrial sector for sustainability in manufacturing. In particular, knowing these properties of Al-Si-Mg alloys used in engine blocks, engine covers, cylinder heads and pistons is important in terms of operating performance and service life in mechanical systems. In this study, Al-7Si-Mg alloy was manufactured by the permanent mould casting (PMC) method and the microstructural, mechanical and machining properties of this alloy in as-cast (ACst) and T6 heat-treated (HTed) states were investigated. Optical microscope (OM) and Scanning Electron Microscope (SEM) imaging processes were used to determine the phases in the microstructure of the alloy. The mechanical properties of the alloy were stated using tensile tests and the Brinell hardness measurement method. Milling tests were applied in the machinability tests, and these tests were realized with TiAlN coated carbide tools on the CNC milling machine using three different cutting speeds- CSs ( V : 50, 80 and 110 m/min), feed rates- FRs ( f : 0.08; 0.16 and 0.24 mm/rev) and constant depth of cut- DoC (1 mm). The microstructure of the ACst alloy consisted of α-Al, primary Si, coral-like eutectic Al-Si, acicular β-Fe (β-Al 5 FeSi) and script-like π-Fe (π-AlSiMgFe) intermetallic phases. After the heat treatment (HT), the present phases in the microstructure partially dissolved and clustered, and these phases coarsened and turned into a spherical morphology. As a result of the HT, the hardness, yield ( YS ) and tensile strength ( TS ) values of the alloy augmented, while the elongation to fracture ( EF ) was reduced. After milling tests, cutting force ( F ), surface roughness ( Ra ), BUL (Built-up layer) and BUE (Built-up edge) values in the ACst and HTed alloys decreased depending on the increase in CS , while they increased with the increase in FR . The results showed that HTed alloys should be subjected to machining operations with a combination of high cutting speed and low feed rate to achieve high mechanical service life and machined surface quality. It was determined that industrial practitioners could increase performance in manufacturing by considering this situation.

Optimization of T6 Heat Treatments for AlSi5Mgx Alloys via Computational Materials Engineering and Experimental Validation for Automotive Applications

Heat Treatment Simulation of Aluminum Alloy Wheels and Investigation of Process Steps

An Experimental Study on Microstructural, Mechanical and Machinability Properties of As-Cast and Heat-Treated Al-7Si-Mg Alloy

Development of an Alternative Heat Treatment to the Traditional T6 Heat Treatment of AlSi10Mg Alloy Produced by Additive Manufacturing

Investigation of metallurgical properties of Al-Si-Mg casting alloys with integrated computational materials engineering for wheel production

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys

Investigation on Heat Treatment of Large-Sized and Complex AlSi9Mg Aluminum Alloy Components Formed by Squeeze Casting

Rotating bending fatigue behavior of high-pressure diecast AlSi10MgMn alloy based on T5 heat treatment parameters

Optimum heat treatment of aluminum alloy used in manufacturing of automotive piston components

Processing of T6 heat-treated Al-12Si-0.6Mg alloy

Effect of chemical composition and T6 heat treatment on microstructure and mechanical properties of a hyper eutectic Al–Si alloy

The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al–Si–Mg–Mn alloys

Effect of T6 Heat Treatment on Microstructure and Mechanical Properties of 6082 Aluminum Alloy Automotive Flange Components Formed by Squeeze Casting

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

OPTIMIZATION OF HEAT TREATMENT SUPPORT FRAMES FOR ALUMINUM ALLOY STRUCTURAL CAST PARTS USING VIRTUAL EXPERIMENTATION

Homogenization heat treatment influence on microstructure evolution and mechanical properties of as-cast Al-Li-Cu-Mg-Zr alloy for lightweight aerospace application