Abstract:In this work, the structural and mechanical properties of ternary Mo-Al-N alloys are investigated by combining thin film growth experiments and density functional theory (DFT) calculations. Mo1−xAlxNy thin films (∼300 nm thick), with various Al fractions ranging from x = 0 to 0.5 and nitrogen-to-metal (Al + Mo) ratio ranging from y = 0.78 to 1.38, were deposited by direct-current reactive magnetron cosputtering technique from elemental Mo and Al targets under Ar + N2 plasma discharges. The Al content was varied by changing the respective Mo and Al target powers, at a fixed N2 (20 SCCM) and Ar (25 SCCM) flow rate, and using two different substrate temperatures Ts = 350 and 500 °C. The elemental composition, mass density, crystal structure, residual stress state, and intrinsic (growth) stress were examined by wavelength dispersive x-ray spectroscopy, x-ray reflectivity, x-ray diffraction, including pole figure and <math> si n 2 ψ</math> measurements, and real-time in situ wafer curvature. Nanoindentation tests were carried out to determine film hardness H and elastic modulus EIT, while the shear elastic constant C44 was measured selectively by surface Brillouin light spectroscopy. All deposited Mo1−xAlxNy films have a cubic rock-salt crystal structure and exhibit a fiber-texture with a [001] preferred orientation. The incorporation of Al is accompanied by a rise in nitrogen content from 44 to 58 at. %, resulting in a significant increase (2%) in the lattice parameter when x increases from 0 to 0.27. This trend is opposite to what DFT calculations predict for cubic defect-free stoichiometric Mo1−xAlxN compounds and is attributed to variation in point defect concentration (nitrogen and metal vacancies) when Al substitutes for Mo. Increasing Ts from 350 to 500 °C has a minimal effect on the structural properties and phase composition of the ternary alloys but concurs to an appreciable reduction of the compressive stress from −5 to −4 GPa. A continuous increase and decrease in transverse sound velocity and mass density, respectively, lead to a moderate stiffening of the shear elastic constant from 130 to 144 GPa with increasing Al fraction up to x = 0.50, and a complex and nonmonotonous variation of H and EIT is observed. The maximum hardness of ∼33 GPa is found for the Mo0.81Al0.19N1.13 film, with nitrogen content close to the stoichiometric composition. The experimental findings are explained based on structural and elastic constant values computed from DFT for defect-free and metal- or nitrogen-deficient rock-salt MoAlN compounds.

Size effect on mechanical properties and deformation mechanisms of highly textured nanocrystalline Mo thin films

Size effect on transverse free vibrations of ultrafine nanothreads

Size dependent mechanical properties and deformation mechanisms in Ti and Zr films

Research on Deforming Mechanism of Nanocrystalline Cu Thin Film under Contact Deformation

Individual Layer Thickness Dependence of Microstructure and Mechanical Properties of Magnetron Sputtering Mo-W-Doped Ni/Ni3Al Multilayers

Size dependent mechanical properties of nanocrystalline Cu films

Grain size dependent microstructure and texture evolution during dynamic deformation of nanocrystalline face-centered cubic materials

The Effect of Size on the Elastic Strain Limit in Ni60Nb40 Glassy Films

Unusual Deformation-Induced Martensitic Transformation in Fe-Co-Ni- Cr-Mn High Entropy Alloy Thin Films

Effect of temperature and strain rate on deformation behavior in metallic glassy films

Size Effects in Internal Friction of Nanocrystalline Aluminum Films

Effect of film thickness on the structural and tribo-mechanical properties of reactive sputtered molybdenum nitride thin films

Mechanical Properties and Deformation Mechanisms of Nanocrystalline U-10Mo Alloys by Molecular Dynamics Simulation

Structure, stress, and mechanical properties of Mo-Al-N thin films deposited by dc reactive magnetron cosputtering: Role of point defects

Size effects on the onset of plastic deformation during nanoindentation of thin films and patterned lines

The effect of molybdenum content on microstructure, mechanical, tribological and corrosion behavior of Zr-Mo-N composite films

Effects of Mo Single‐Layer Thickness on Microstructure and Tribological Behavior of WS x /Mo/a‐C/Mo Multilayer Films

Indentation Size Dependent Plastic Deformation of Nanocrystalline and Ultrafine Grain Cu Films at Nanoscale

Size effects and plastic deformation mechanisms in single-crystalline CoCrFeNi micro/nanopillars

Effect of Loading Rate on Creep Behavior and Shear Transformation Zone in Amorphous Alloy Thin Films, and Its Correlation with Deformation Mode Transition

Thickness Dependent Microstructures and Properties of Sr2Fe10/9Mo8/9O6 Films Grown in N2